Switching On/Off; Maintenance And Service; Maintenance And Cleaning - Bosch UniversalGrind 750-115 Manual Original

When carrying out abrasive cutting, use a moderate feed
that is suited to the material being machined. Do not exert
pressure on the cutting disc and do not tilt or swing the
power tool.
Do not attempt to reduce the speed of a cutting disc coming
to a stop by applying pressure from the side.
Cutting stone
For cutting stone with bonded cutting discs or dia-
u
mond cutting discs for concrete/stone, always use the
extraction guard for cutting with a cutting guide (21)
or the protective guard for cutting (5) or the protect-
ive guard for grinding (6) with a fitted cover for
cutting (7).
Provide sufficient dust extraction when cutting stone.
u
Wear a dust mask.
u
The power tool may be used only for dry cutting/grind-
u
ing.
When using the protective guard for cutting (5) , the
u
protective guard for grinding (6) or the protective
guard for grinding (6) with a fitted cover for
cutting (7) for cutting and grinding applications in
concrete or masonry, there is an increased dust load
and an increased risk of losing control of the power
tool, which can lead to kickback.
For cutting stone, it is best to use a diamond cutting disc.
When using the extraction guard for cutting with a cutting
guide (21), the dust extractor must be approved for extract-
ing stone dust. Suitable dust extractors are available from
Bosch.
crete with a high pebble content, the diamond cutting disc
can overheat and become damaged as a result. This is
clearly indicated by circular sparking, rotating with the dia-
mond cutting disc.
If this happens, stop cutting and allow the diamond cutting
disc to cool down by running the power tool for a short time
at maximum speed with no load.
Bosch Power Tools
The power tool must always
work in an up-grinding mo-
tion. Otherwise there is a
risk that it will be pushed
uncontrolled out of the cut.
For best results when cut-
ting profiles and rectangular
tubing, start at the smallest
cross section.
Switch on the power tool
and position it with the
front part of the cutting
guide on the workpiece.
Move the power tool with a
moderate feed motion that
is suited to the material be-
ing machined.
When cutting especially
hard materials such as con-
If work is noticeably slower and with circular sparking, this
indicates that the diamond cutting disc has become blunt.
You can resharpen the disc by briefly cutting into abrasive
material (e.g. lime-sand brick).
Information on structural design
Recesses in load-bearing walls are subject to country-spe-
cific regulations. These regulations must be observed under
all circumstances. Seek advice from the responsible struc-
tural engineer, architect or construction supervisor before
starting work.
Start-Up
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
When operating the power tool using a mobile generator that
does not have sufficient reserve capacity or an adequate
voltage control system with inrush current boost converter,
loss of performance or atypical behaviour may occur upon
switch-on.
Please check the suitability of the power generator you are
using, particularly with regard to the mains voltage and fre-
quency.

Switching on/off

To start the power tool, push the on/off switch (3) forward.
To lock the on/off switch (3) in position, push the on/off
switch (3) forward and down until it clicks into place.
To switch off the power tool, release the on/off switch (3);
or, if the switch is locked, briefly push the on/off switch (3)
backward and down and then release it.
Always check abrasive tools before using them. The
u
abrasive tool must be fitted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use abrasive tools that are
damaged, run untrue or vibrate during use. Damaged
abrasive tools can burst apart and cause injuries.

Maintenance and Service

Maintenance and Cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Store and handle the accessories carefully.
English | 23
1 609 92A 705 | (19.04.2022)