Intended Use; Technical Data; Before Starting The Equipment; Assembling The Equipment - EINHELL TE-VC 36/30 Li S Manual De Instrucciones

3. Intended use

The cordless wet/dry vacuum is designed for wet
and dry vacuuming using the appropriate fi lter.
The equipment is not suitable for the vacuuming
of combustible, explosive or harmful substances.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: .............36 V
Air fl ow: ............................ 56 CFM (1.59 m³/min)
Sealed suction:
BOOST: ...................... 59'' (water lift) (150 mbar)
ECO: ........................... 40'' (water lift) (100 mbar)
Vacuum hose length: ....................... 8.2 ft (2.5 m)
Tank capacity: .............................. 8 Gallon (30 l )
Weight: .......................................... 17.6 lbs (8 kg)

5. Before starting the equipment

5.1 Assembling the equipment

Fitting the appliance head (Fig. 1/5)
The equipment head (3) is fastened to the
tank (7) by the locking hook (6). To remove the
equipment head (3), open the locking hook (6)
and take off the equipment head (3). When fi tting
the equipment head (3), make sure that the
locking hook (6) locks into place correctly.
Fitting the wheels (Fig. 7-13)
Place a split pin for fi tting the wheels (29)
through the appropriate hole in the axle (31)
and fi t a washer (28), a wheel (22) and a washer
to the axle (31) (Fig. 7-8). Now slide the axle
(31) through the guides provided for it on the
underside of the tank (7) (Fig. 9). Fit a washer and
the second wheel (22) to the empty end of the
axle (31) and secure it with the other washer (28)
and the split pin (29) (Fig. 10-12). Push the covers
Anl_TE_VC_36_30_Li_S_USA_SPK7.indb 9 Anl_TE_VC_36_30_Li_S_USA_SPK7.indb 9
EN
(30) on to the outside of the wheels (22) so that
the detents engage on the covers (30) for the
wheel (22). (Fig. 13)
Fitting the castors (Fig. 6/Item 13)
Fit the castors (13) into the appropriate mountings
on the underside of the tank (7). Push the castors
(13) fi rmly into the mounting until they engage
with a clicking noise (Fig. 6).
Fitting the push bar (Fig. 18)
Fit the push bar handle (35) onto the push bar
mounts (38) of the tank and secure the push bar
with the supplied screws (32) and fastening nuts
(36) as shown in Figure 18.
5.2 Fitting the fi lters
Important!
Never use the wet/dry vacuum without a fi lter.
Always ensure that the fi lters are securely seated.
Fitting the foam fi lter (Fig. 14/Item 15)
For wet-vacuuming, slip the supplied foam fi lter
(2x 18 V)
(15) over the fi lter basket (Fig. 4/Item 4).
Fitting the pleated fi lter (Fig. 15)
For dry-vacuuming, slip the pleated fi lter (Fig. 18)
onto the fi lter basket (Fig. 4/Item 4) and secure
in place by rotating clockwise until the locking
knobs connect. The pleated fi lter is suitable for
dry-vacuuming only.
Fitting the dust bag (Fig. 17/Item 14)
For vacuuming fi ne, dry dirt it is recommended
that you fi t the dust bag (Fig. 2/Item 14). Slip
the dust bag (14) over the vacuuming hole. The
dust bag (14) is suitable for dry-vacuuming only.
The dust bag makes it easier to dispose of the
sucked-in dust.
5.3 Fitting the suction hose (Fig. 17/Item 10)
Connect the suction hose (10) to the
corresponding connector on the wet/dry vacuum,
depending on the application required.
Vacuuming
Connect the suction hose (10) to the suction hose
connector (8).
Blowing
Connect the suction hose (10) to the blow
connector (9).
- 9 -
13.04.2022 14:00:33 13.04.2022 14:00:33