General Instructions; Unit Characteristics - Tecnoinox PF70G7 Manual De Instrucciones Para El Uso Y Manteniminto

Part 1
GAS RANGES
The appliance described in this manual has been built to meet UNI EN
203, UNI EN 437, EN 60335-1, EN60335-2-36 and EN55014 standards.
This appliance has been designed exclusively for cooking food, any
other use is considered improper.
The appliance should be installed under an extractor hood for removing any cooking fumes.
Care must be taken when using the appliance because the cooking surfaces are very hot.
The appliance must be installed, connected and serviced properly by qualified personnel according to the regulations and directives in
force in the country where it is installed, as well as the instructions in this manual.
These installation and user's instructions refer to the category II2H3+ gas
ranges.
The self-adhesive polyester data plate "T" (fig.8) is behind the control
panel (inside the appliance).
It contains the following information:
Model
Serial n.
Category
Year of manufacture
Nominal thermal capacity [kW]
Type of construction
Test base
Connection pressure
Consumption
The supplementary plate is also made of self-adhesive polyester and is
affixed near the data plate; it contains all information regarding the
appliance.
Before you install the appliance, make sure that the gas
company has authorised the installation, compare the data
relevant of the appliance (data plate) with the local supply.
Remove the packaging from the appliance as well as the protective
plastic sheet, and, if necessary, remove traces of glue with a suitable
solvent. To dispose of the packaging, follow local directives (for more
details refer to the chapter "ECOLOGY AND THE ENVIRONMENT".
Prior to connecting the unit to the gas network, check the data plate to
see if the unit has been set and tested for the type of gas supplied. If the
gas type indicated on the data plate is not the same as that supplied,
please refer to the paragraph "CONVERSION AND ADAPTATION".
Connect the appliance to the gas distribution network using metal pipes
with a suitable diameter; install a homologated shut-off cock between the
appliance and the distribution network. If flexible pipes are used they
must be made of stainless steel according to the standards in force.
When installing the appliance, all the regulations in force must be
observed, such as:
UNI-CIG 8723 safety standard, Act n.46 of the 5th of March 1990
and circular n.68.
Regional and/or local regulations, such as building codes;
Directives and regulations of the electricity board.
Accident prevention regulations in force;
Fire prevention regulations;
Applicable I.E.C. regulations.
All manuals and user guides at all-guides.com
PF70G7
xxx
II2H3+
xxx
19,5
A
UNI EN 203-1
G30
28-30/37 mbar
G20
20 mbar
G30 [Kg/h] 1,54
3
G20 [m /h]
2,06
Connection to the gas distribution network.

General Instructions

It should only be used by qualified personnel in professional kitchens.
The unit must never be left unattended when it is being used! The
appliance should be checked once a year by a qualified technician.
Switch the appliance off in the case of a failure or malfunction.

Unit characteristics

Model
PF70G7
PF105G7
PF70GG7
PF105GG7
PFP70GG7
PFP105GG7
PPF70GG7
PFX105GG7
PFX105G7
The " " gas distribution network fitting (fig.1) meets ISO 7/1 and ISO
228/1 (DK) standards with a ø ½" connection, situated at the back of the
machine. The structure of the appliance is made of stainless steel, the
burners are made of cast iron and the oven is made of stainless steel. All
models have adjustable feet. The main gas pipe is made of galvanised
steel. The pipes between the tap and burner are made of copper.
Install a shut-off cock in the line between the appliance and
the gas distribution network. Install an omnipolar switch
between the appliance and the electrical distribution network.
We recommend installing the appliance in a well-ventilated environment,
or under an extraction hood to remove the fumes or vapours produced
during the cooking cycle.
All models have an equipotential earth terminal " " (fig.1) in the bottom.
The appliances with an electric oven have a hole for the cable " " (fig.1).
The appliance can be installed alone or in line. Respect a minimum
distance of 80mm between the appliance and any walls made of
flammable material, partitions, kitchen furniture or nearby equipment.
The contact surfaces must be covered with non-combustible heat
insulating material. The appliance, and especially the power lead, must
not be installed anywhere near heat sources and the temperature of the
place in which the appliance is installed must not rise above 50°C. After
installing the appliance check for any leaks in the fittings. Use non-
corrosive foam products, such as leak detection sprays, to look for any
leaks.
When checking for leaks do not use naked flames!
The manufacturer shall not be held responsible and the
guarantee is void in the case of damage caused by
negligence in following the operating and installation
instructions or by improper use. The guarantee is void in the
case of connections which have been made in a way which
doesn't meet the current standards and fire-fighting
regulations.
GB / IE - 1
N. of burners Rings [kW]
4 3.3 +[4.5] × 2+7.2
6 [3.3+4.5+7.2] × 2
4+1 3.3 +[4.5] × 2+7.2
6+1 [3.3+4.5+7.2] × 2
3+1 3.3+4.5+7.2
5+1 [3.3+4.5] × 2+7.2
1+1 9
6+1 [3.3+4.5+7.2] × 2
6 [3.3+4.5+7.2] × 2
Installation
Oven
4,7kW
4,7kW
7kW
7kW
7kW
7kW
7kW
7kW
6,3kW
5410.265.03