Makita CL003G Manual De Instrucciones página 15

OPERATION
CAUTION:
Do not move your face close to
the air vent when operating the cleaner. If foreign
objects are blown into eyes, it may result in personal
injury.
NOTICE:
Avoid using the cleaner in a horizontal
or upward facing position. It may otherwise cause
the mesh filter to become clogged.
NOTICE:
Always use the cleaner with filters
installed. Using the cleaner without filters may result
in a motor malfunction.
NOTICE:
Empty the dust case in the cyclone unit
when dust has accumulated. Continued use will
result in weakened suction force.
The cyclone unit helps reduce the amount of dust that
enters into the cleaner, enhancing the suction perfor-
mance with simple and easy dust disposing.
Cleaning (Suction)
Nozzle
With 250 mL dust case only
Attach the nozzle to clean off tables, desks, furniture,
etc. The nozzle slips on easily.
► Fig.10: 1. Nozzle
Nozzle + Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a floor in a standing position.
► Fig.11: 1. Cleaner body 2. Extension wand
3. Nozzle
Corner nozzle
Fit on the corner nozzle for cleaning corners and crev-
ices of a car or furniture.
► Fig.12: 1. Corner nozzle 2. Cleaner body
You can store the corner nozzle in the nozzle holder.
► Fig.13: 1. Nozzle holder 2. Corner nozzle
CAUTION:
Be careful not to trap finger(s)
between the corner nozzle and the nozzle holder.
Trapping finger(s) may cause injury.
Corner nozzle + Extension wand
(Straight pipe)
In tight quarters where the cleaner itself cannot
squeeze in, or in high places hard to reach, use this
arrangement.
► Fig.14: 1. Corner nozzle 2. Extension wand
3. Cleaner body
Cleaning without nozzle
With 250 mL dust case only
You can pick up powder and dust without nozzle.
► Fig.15
For picking up dust on a floor in a standing position, it is conve-
nient to attach the extension wand (straight pipe) to the cleaner.
► Fig.16: 1. Extension wand
Disposing of dust
CAUTION:
Empty the dust case before it
becomes too full, or the suction force weakens.
CAUTION:
Be careful not to trap finger(s)
between the dust case and cyclone body when
reassembling.
Dispose of accumulated dust as follows before it
exceeds the dust disposal line.
1. Point the cleaner head downwards, hold the dust case
firmly, and then pull it apart from the cyclone body while pressing
and holding the release buttons on both sides of the dust case.
► Fig.17: 1. Dust disposal line 2. Dust case
3. Release buttons 4. Mesh filter
2. Empty the dust case and clean the adhered dust
off the mesh filter.
► Fig.18
3. Place the dust case back onto the cyclone body to
secure it in place with clicks.
► Fig.19: 1. Dust case 2. Release buttons 3. Cyclone body
CAUTION:
The dust may fly up when dis-
posed out of the dust case. Be careful not to let
the dust get into your eyes.
NOTICE:
When the dust case becomes dirty,
remove and wash it with water. Dry the dust case
thoroughly before reassembly and use.
NOTICE:
Make sure all the attachments and
components are secured in place properly before
use.
NOTICE:
If the suction force does not recover
even after disposing of the dust and cleaning the
mesh filter, check whether dust has accumulated
inside the cyclone body or clogging has occurred.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed before
attempting to perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
15 ENGLISH