Troubleshooting - FoodSaver FM2400 Serie Manual Del Propietário

Troubleshooting

Problem Solution
• Unit is overheated. Always allow 20 seconds between seals. Under heavy
usage, appliance will shut off automatically and Red Light will flash. Wait
for 20 minutes for unit to cool off.
Red Seal LED • Always wait 20 seconds between seals.
flashing
• Latch has been left in Operate position: Gaskets may be compressed.
Turn Latch to Open or Store position and allow 10-20 minutes for Gaskets
to expand.
• Vacuum pump running more than 120 seconds. Under heavy usage,
appliance will shut off automatically and Red Light will flash. See next
section 'Vacuum Pump is running, but bag is not evacuating air'.
• If making a bag from a Roll, make sure one end of bag is sealed.
(See "How to Make a FoodSaver
• Adjust the bag and try again. Make sure the open end of the bag is down
inside the Drip Tray.
Vacuum Pump is
• Check for wrinkles in bag along Sealing Strip. To prevent wrinkles in the
running, but bag
seal, gently stretch bag flat while inserting bag into Drip Tray.
is not evacuating
• Open unit and make sure Gaskets are inserted properly and there are no
air
foreign objects, dirt or debris on the Upper or Lower Gaskets. (See "Care
& Cleaning" on pg 11.)
• If Latch has been left in Operate position during storage: Gaskets may
be compressed. Turn Latch to Open or Store position and allow 10 to 20
minutes for Gaskets to expand.
• Make sure the accessory hose is not attached to accessory port.
• Make sure the lid is latched down all the way. If the Latch does not catch
the lid and bring it down, there will be a leak between the Gaskets.
Gasket is loose • Take out the Gasket, clean it and re-insert the Gasket into the Gasket
or has a tear
Channel. (See "Care & Cleaning" on pg 11.)
• Contact consumer services at the number or website listed below.
• Too much liquid in bag, freeze before vacuuming.
• Check for food debris around seal area. If present, take out the Gasket,
Bag is not
clean it and re-insert the Gasket into the Vacuum Channel. (See "Care &
sealing properly
Cleaning" on pg 11.)
• Bag has wrinkles: To prevent wrinkles in the seal, gently stretch bag flat
while inserting bag into Vacuum Channel.
No lights on the
• Make sure unit is plugged in.
control panel
• Make sure wall outlet is functional.
• Make sure lid is all the way down, and the Latch is in the Operate position.
19 US: www.FoodSaver.com | CA: www.FoodSaver.ca | MX: www.oster.com.mx/foodsaver
FM2400_22EFSM1.indd 19-20 FM2400_22EFSM1.indd 19-20
Bag" on pg 7.)
®
Troubleshooting
Problem Solution
Nothing happens when • Make sure unit is plugged in.
Latch is closed and • Make sure wall outlet is functional.
Button is pressed
• Open Latch, make sure lid is all the way down, re-latch lid.
• Make sure there is enough bag material to reach center of Drip Tray. Always
allow three inches (7.62 mm) of extra space to allow the bag to seal tightly
Cannot insert bag
around food contents.
into machine
• Gently stretch bag flat while inserting. Insert bag curled down into Drip
Tray.
• Examine the seal. A wrinkle along the seal may cause air to re-enter the
bag. To prevent wrinkles in the seal, gently stretch bag flat while inserting
bag into Drip Tray.
• Sometimes moisture or food material (such as juices, grease, crumbs,
powders, etc.) along seal prevents bag from sealing properly. Cut bag open,
Air was removed from
wipe top inside of bag and re-seal.
the bag, but now air
• Sharp food items may have punctured bag. Use a new bag if there is a
has re-entered
hole. Cover sharp food items with a soft cushioning material, such as a
paper towel, and re-seal.
• Fermentation or the release of natural gases from inside the foods may
have occurred. When this happens, food may have begun to spoil and
should be discarded.
• Faulty bag. Bag could be punctured. Try another bag.
• Sealing Strip may have become too hot. Always wait at least 20 seconds
for appliance to cool down before you vacuum seal another item.
Bag melts
• Use FoodSaver ® brand bags. Our FoodSaver
designed for FoodSaver
• The FoodSaver Container Lid must be correctly aligned with the Container
®
opening. (See "Owner's Manual" provided with accessory.)
Container does not
• Assure the green end of the accessory cable marked 'To Sealer' is pushed
vacuum
into the unit until you hear it "click".
• Make sure Container Lid is closed securely on all 4 sides of the Container.
• Make sure rubber Gasket on inside of Lid is free from food residues.
• Examine Container rim for cracks or scratches and make sure Container
valve is clean.
If you need further • Contact consumer services at the number below or visit the website and
assistance: click the 'Support' tab.
Consumer Service: US: 1-877-777-8042 CA: 1-877-804-5383 MX: +52 55 5366 0800
® Bags and Rolls are specially
® units.
2022/2/23 上午9:16 2022/2/23 上午9:16
20