Troubleshooting Guide; Warranty; Technical Data; Declaration Of Conformity - Kärcher PCL 3-18 Manual De Instrucciones

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the battery pack.
WARNING
Uncontrolled startup
Risk of injury
Remove the battery pack from the device during work
breaks and before carrying out any service or care work.
ATTENTION
Danger of burns
The gearbox can be very hot after use. Allow the device
to cool down before replacing the brushes.
1. Remove the battery pack (see chapter Removing
the battery pack).
Illustration O
2. Unscrew and remove the brush fasteners.
3. Pull out the worn brushes.
4. Fit the new brushes.
5. Fit and tighten the brush fasteners.
Note
Pay attention to the assignment when fitting the brush
fasteners (left / right, as seen on the type plate)!
Cleaning the water filter
Note
If the water flow is inadequate then the water filter of the
device must be cleaned.
Illustration P
1. Unscrew the plug connector at the water connec-
tion.
2. Pull out the water filter.
3. Clean the water filter under running water against
the direction of flow.
4. Insert the water filter.
5. Screw on the plug connector.
Ensure that the sealing ring in the plug connector has
been inserted correctly.
Cleaning the device
WARNING
Uncontrolled startup
Risk of injury
Remove the battery pack from the device during work
breaks and before carrying out any service or care work.
ATTENTION
Improper cleaning
Damage to the device
Do not clean the device with a hose or high-pressure
water jet.
Do not use aggressive detergents.
Do not knock the brush on the ground.
1. Remove the battery pack (see chapter Removing
the battery pack).
2. Remove soiling, plant residue and sand/stone from
the brushes.
3. If necessary, remove the brushes and clean them
under running water.
4. Clean the device with a moist cloth.

Troubleshooting guide

Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Device switches off during operation
The motor circuit breaker has triggered
 Allow the device to cool down (at least 10 minutes).
The motor circuit breaker resets automatically and
the device is ready for operation again.
The trigger must not be pressed during the cool-
ing phase to avoid the device starting up unex-
pectedly. Always wait for the specified cooling
time before restarting the device.
In case of a repeated shut-down, reduce the pres-
sure on the brushes while cleaning and hold the de-
vice at a flatter angle.
Device not running
The battery pack is not sitting properly in the device
1. Push the battery pack into the mounting in the de-
vice until it audibly latches into place.
The charging state of the battery pack is too low
1. Charge the battery pack.
The battery pack is overheated
1. Remove the battery pack from the device and allow
it to cool down.
2. Do not the place the device and battery pack in di-
rect sunlight.
The battery pack or the charger are defective
1. Replace the battery pack or charger.
Unsatisfactory cleaning results
Dirty brushes
 Clean the air brushes.
Worn brushes
 Replace the brushes.
Clogged water filter
 Cleaning the water filter
 Replace the water filter
Clogged water nozzles
 Have the water nozzles replaced by an authorised
Customer Service department.
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Technical data

Device performance data
Nominal voltage
Degree of protection
Brush speed
Brush diameter
Dimensions and weights
Weight
Length x width x height
Subject to technical modifications.

Declaration of Conformity

EU Declaration of Conformity
We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in cir-
English

Warranty

V 18
IPX1
1/min 500-600
mm 100
kg 5,6
mm 770 x 395 x 240
13