Tabla de contenido
Idiomas disponibles
Idiomas disponibles
13. 2 ELECTROMAGNETIC IMMUNITY
The I
C
is intended for use in the electromagnetic environment specified in the table below.
MPLANT
ENTER
The user and/or installer must ensure that the I
environment.
Immunity test
IEC 60601 test level
Electrostatic
± 6KV contact
discharge (ESD)
± 8KV air
IEC 61000-4-2.
Electrical fast
transients
± 2KV for power supply lines
IEC 61000-4-4.
Surges
± 1KV differential mode
IEC 61000-4-5.
± 2KV common mode
<5% UT
T
cycles.
40% U
(60% dip in U
T
Voltage dips, short
cycles
interruptions and
voltage variations
70% U
(30% dip in U
T
IEC 61000-4-11.
cycles
<5% U
(>95% dip in U
T
cycles
13. 3 ELECTROMAGNETIC IMMUNITY / MOBILE RADIOFREQUENCY EQUIPMENT
The I
C
is intended for use in the electromagnetic environment specified in the table below.
MPLANT
ENTER
The user and/or installer must ensure that the I
environment.
Immunity test
IEC 60601 test level
Portable and mobile radiofrequency communications devices must not be used near the I
than that recommended and calculated according to the frequency and power of the emitter.
Conducted
disturbance,
radiofrequency fields.
150 KHz to 80 MHz
IEC61000-4-6
Radiated
radiofrequency
electromagnetic
80 MHz to 2.5 GHz
field.
IEC61000-4-3
The electromagnetic field strengths of fixed radiofrequency emitters, as determined by an electromagnetic environment measurement (a),
must be less than the compliance level in each frequency range (b).
Interference may occur near equipment marked with the symbol below:
24
All manuals and user guides at all-guides.com
± 6KV contact
± 8KV air
± 2KV for power supply lines
± 1KV differential mode
± 2KV common mode
(>95% dip in U
) for 0.5
<5% U
T
cycles.
) for 5
40% U
T
cycles
) for 25
70% U
T
cycles
) for 250
<5% U
T
cycles
Compliance level
3 V/m
3 V/m
C
is used in such an electromagnetic
MPLANT
ENTER
Compliance level
Floors must be wood, concrete, cement or tiled.
If floors are covered with synthetic material
(carpet, etc.), the relative humidity must be at
least 30%.
Mains power quality should be that of a typical
commercial or hospital environment (hospital,
clinic).
Mains power quality should be that of a typical
commercial or hospital environment.
(>95% dip in U
) for 0.5
T
T
Mains power quality should be that of a typical
(60% dip in U
) for 5
T
T
commercial or hospital environment.
If the use of the I
operation during power mains interruption, it is
(30% dip in U
) for 25
T
T
recommended that the product be powered from a
separate power supply (UPS, etc.).
(>95% dip in U
) for 250
T
T
C
is used in such an electromagnetic
MPLANT
ENTER
Electromagnetic environment - guidance
MPLANT
Recommended separation distance:
3 V/m
d = 1.2
d = 1.2
80MHz à 800MHz.
d = 2.3
800MHz à 2.5GHz.
3 V/m
Where P is the maximum power rating of the emitter in watts
(W) according to the manufacturer's specifications and d is the
recommended minimum separation distance in meters (m).
Electromagnetic environment - guidance
C
requires continued
MPLANT
ENTER
C
(including its cables) at a distance less
ENTER
Tabla de contenido
