(t. 1
Cycle time for OUT1 relay or
-
logic output = HEAT or COOL
71
(t. 2
Cycle time for OUT2 relay or
-
logic output = HEAT or COOL
72
(t. 3
Cycle time for OUT3 relay or
-
logic output = HEAT or COOL
73
(t. 4
Cycle time for OUT4 relay or
-
logic output = HEAT or COOL
74
Fault action (sets state in case of probe
rel.
fault) Alarm outputs AL1, AL2, AL3; Select
-
intrinsic safety
75
_rEL.
Alarm 1
0
OFF
1
ON
2
OFF
3
ON
4
OFF
5
ON
6
OFF
7
ON
Note:
1) In case of broken probe, logic state of individual alarm
assumes selected logic value without consideration of alarm
type (direct or inverse): ON=alarm active;
OFF=alarm inactive
2) Assign alarms to available outputs by entering codes rLo1,
rLo2, rLo3, rLo4.
An. o . i
Assignment of signal or reference value: PV, SP,
SP-PROG, DEV+, DEV-, IN.AUX, HEAT, COOL,
AL1, AL2, AL3, serial line value
78
An.o.x Reference value
0
PV - process variable
1
SSP - active setpoint
2
-
3
InP.2 - aux input
4
Deviation (SSP-PV)
5
HEAT (*)
6
COOL (*)
7
AL1 (alarm point)
8
AL2 (alarm point)
9
AL3 (alarm point)
10
AL.HB - (alarm point)
11
Value acquired from serial line
12
Setpoint slaved to programmer
+ 16 for inverted output with respect to reference value
+ 32 for output with 2...10V, 4...20mA signal
(*) - Fixed scale limits
- Retransmission output not available with ON/OFF control action
Minimum limit of
l. a n. i
analogue repetition
signal output 1
76
Maximum limit of
x. a n. i
analogue repetition
signal output 1
77
An. o . 2
Assignment of signal or reference value: PV, SP,
SP-PROG, DEV+, DEV-, IN.AUX, HEAT, COOL,
AL1, AL2, AL3, serial line value
81
Minimum limit of
l. a n. 2
analogue repetition
signal output 2
79
Maximum limit of
x. a n. 2
analogue repetition
signal output 2
80
Prot
Protection
Prot
0
code
1
2
42
3
+4 to disable InP, Out
+8 to disable CFG, Ser
+16 to disable SW "power-up - power down"
1. ... 200 sec
(0.1...20.0 sec)
1. ... 200 sec
1. ... 200 sec
1. ... 200 sec
Alarm 2
Alarm 3
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
Out W1
An.o.1, An.o.2
-1999...9999
-1999...9999
Out W2.
-1999...9999
-1999...9999
• Prot
Dispaly
SP, InP2, alarms, OutP, INFO, DATA
SP, InP2, alarms, OutP, INFO, DATA
SP, InP2, alarms, OutP, INFO
SP
+32 disable manual power latching
+64 to disable manual power modification
Hrd
Hardware configuration
SP. P t
Programmer
installation and
resource
selection
(*) as alternative to the custom input linearization function
sp. p r
Programmer
function
hrd. i
Installation of aux
input, digital inputs,
serial interface
hrd. 2
Installation of
relay, logic
outputs
MAIN, AL1,
AL2, AL3,
and analogue
outputs W1,
W2
"*" key and
xrd. 3
bargraph
installation
(trl
Control type
[0...78]
43
Modification
SP, alarms, DATA
SP, alarms
SP
25
• Hrd
SP.Pt
Type of programmer
0
Programmer disabled
(with programmer disabled,
operation is as described in the
1600/1800 controller manual)
1
12-step programmer without
control parameters group
2 (*)
12-step programmer with
control parameter groups
3 (*)
16-step programmer without
control parameter groups
SP.Pr
1
Program selection from keypad;
time base HH : MM
2
Program selection from digital inputs;
time base HH : MM
+ 4 time base HH : MM
+ 8 to enable slaved setpoint
+ 16 to enable 4 events (ramp and/or hold)
+ 32 to enable step advance from digital inputs
+ 64 to enable Hold Back Band
hrd.1
Aux
Logic
analogue
input 1
input
(IN1)
0
1
x
2
x
3
x
x
4
5
x
6
x
7
x
x
8
9
x
10
x
11
x
x
12
13
x
14
x
15
x
x
hrd.2
OUT1
OUT2
(relé, logic) (relé, logic) (relé, logic)
0
1
x
2
x
3
x
x
4
5
x
6
x
7
x
x
8
9
x
10
x
11
x
x
12
13
x
14
x
15
x
x
+ 16 to enable analogue output W1
+ 32 to enable analogue output W2
+ 64 to invert state of LEDs compared to state of output
Hrd.3 Taste "*" Bargraph
0
1
x
2
x
3
x
x
CtrL
Control type
0
P heat
1
P cool
2
P heat / cool
3
PI heat
4
PI cool
5
PI heat / cool
6
PID heat
7
PID cool
8
PID heat / cool
9
ON-OFF heat
10
ON-OFF cool
11
ON-OFF heat / cool
12
PID heat + ON-OFF cool
13
ON-OFF heat + PID cool
14
PID heat + cool with relative gain
(see C.MEd parameter)
Selection of derivative action sampling time:
+ 0
sample 1 sec.
+ 16 sample 2 sec.
+ 32 sample 8 sec.
+ 64 sample 240 msec.
Alarm is not enabled with ON/OFF type control.
Logic
Serial
input 2
interface
(IN2)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
OUT3
OUT4
(relé, logic)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x