Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL CE-CP 18/180 Li E Manual De Instrucciones

•
Excessive pressure results in poor perfor-
mance and early wearing of the accessory
used. Sensitive surfaces may be damaged
e.g. due to excessive speed or too high a
contact pressure.
Important! Adjust the speed to the surface to
be worked before applying the machine to it
and allow the machine to run up to the selected
speed. Depending on the speed, this may take a
few seconds. Particularly when working with the
foam plastic pad, the speed may fl uctuate due
to diff erent surface qualities (diff erent friction) in
the lower speed ranges. This is not an equipment
defect.
Use the foam plastic pad to apply the
polishing agent (Fig. 10).
•
First work on the large level surfaces such as
the engine hood, boot lid and roof.
•
Spread a little polish at points over the foam
plastic pad. Press the foam plastic pad onto
the surface to be polished several times.
The polish is pressed into the foam plastic
pad and transferred onto the surface to be
polished. This prevents the polish on the foam
plastic pad from being sprayed around when
the machine is switched on.
•
Apply the polish at low speed.
•
Only work smaller sections in one go.
•
Work the sections evenly, crosswise and
lengthwise (first vertically, then horizontally).
•
Then move on to working the smaller areas
(e.g. doors).
Finish-polishing
•
Use the synthetic polishing attachment (Fig.
11b) to remove the layer of polishing agent
and finish the polishing work.
•
To fit the synthetic polishing attachment,
pull the edge upwards (Fig. 11a), press the
attachment onto the hook-and-loop surface
of the polishing disk and then pull the edge
downwards again (Fig. 11b). The edge of the
polishing disk is covered by the polishing
attachment.
•
Important! Do not exert any pressure on the
polishing machine!
Care tips
•
Wash your car at least every 2 weeks. Avoid
using household detergents as these can da-
mage the paintwork and remove the layer of
wax.
•
Wash your car with a clean sponge, working
Anl_CE_CP_18_180_Li_E_Solo_SPK13.indb 21 Anl_CE_CP_18_180_Li_E_Solo_SPK13.indb 21
GB
from top to bottom.
•
Remove all insects, bird droppings and tar
stains from the paintwork daily.
•
If you use any window-cleaning agents, spray
them onto a cloth and not directly onto the
windows in order to prevent them wetting the
paintwork.
6.2 Using as a sanding machine
Use the supplied sanding attachments (Fig. 12)
for sanding purposes.
The hook-and-loop fastener enables easy chan-
ging of the sanding attachments.
•
Place the whole surface area of the sanding
disk on the material.
•
Move the machine with gentle pressure over
the „workpiece", making circular or transverse
and linear movements.
•
Use a coarse grit for coarse sanding and a
finer grit for finish sanding. You can find the
best grit size for the job by carrying out san-
ding tests.
6.3 Speed Control Display (Fig. 3)
Use the speed control to set the desired working
speed.
Press the "+" button to increase the speed.
Press the "-" button to decrease the speed.
Refer to the display (8) for the set speed. Set
speed = Display x 100
Important! Adjust the speed to the surface to be
worked before applying the machine, and allow
the machine to run up to the selected speed.
Depending on the speed, this may take a few
seconds.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
- 21 -
11.04.2022 13:14:25 11.04.2022 13:14:25