Important - Worx WG322E Manual Original

NOTE: The tension is automatically increased while the
Chain Tensioning Knob (8) is being turned in a clockwise
direction. The built-in ratchet mechanism prevents the
chain tension from loosening.
3. Tilt the saw forward (See E1) where the Guide Bar (6) tip
is pushed in an upward direction. This will remove slack
from the chain.
4. Fully tighten the Chain Tensioning Knob (8) by turning it
clockwise.
5. Double check the tension set by the automatic Chain
Tensioning Knob. The correct chain tension is reached
when the Chain (7) can be raised approx. half the
drivelink depth from the Guide Bar (6) in the center. This
should be done by using one hand to raise the chain
against the weight of the machine. (See Fig. E2)
NOTE: The Chain (7) is properly tensioned when it can be
lifted off of the Guide Bar (6) and the drivelink is within the
rail of the Guide Bar (6).
NOTE: The Chain (7) will stretch while cutting and lose
proper tension. When the chain becomes loose, completely
unscrew the Chain Tensioning Knob (8) or turn the knob
around three full turns in a counter-clockwise direction,
then retighten the Chain Tensioning Knob (8) to properly
reset the chain tension by repeating Steps 1-4 listed above.
ASSEMBLING THE EXTENSION POLE (Only for WG323E,
WG323E.9)
Align and insert the handle of extension pole into the shaft.
Rotate the locking knob clockwise to lock. (SEE Fig. F1, F2)
NOTE: Make sure that the shaft is firmly locked in place.
ASSEMBLING THE EXTENSION POLE TO THE MACHINE
18
(See Fig G1)
Step1: Align and insert the pole connection bracket (29) into
the saw.
Step2: Turn the Locking Knob (28) counterclockwise to
tighten the extension pole to the machine.
NOTE: Make sure the extension pole is locked into
position securely before operation.
REMOVING THE EXTENSION POLE (See Fig. G2)
Step1: Turn the Locking Knob (28) clockwise to loosen and
pull it out.
Step2: Slide saw to disconnect the extension pole with the
saw.
WARNING!
• When using this machine with the Extension Pole,
make sure that the battery pack has been removed.
Adjusting pole length
The pole saw has a telescoping pole assembly that will
extend from 2m (fully retracted) to 2.7m (fully extended).
Clamping level (26) is used to hold the pole in position at
any extended length.
1. To extend the pole, loosen the clamping lever as shown
in Fig H. Pole will slide freely.
2. Pull inner pole section out to desired length of
extension. Note: only extend pole to minimum length
required to reach limb that is being cut.
3. To lock pole in position, tighten clamping lever as shown
in Fig. H.
LUBRICATION
Cordless Chain Saw
IMPORTANT: The chain saw is not filled with oil.
It is essential to fill with oil before use. Never
operate the chain saw without chain oil or at an
empty oil tank level, as this will result in extensive
damage to the product.
NOTE: Chain life and cutting capacity depend
on optimum lubrication. Therefore, the chain is
automatically oiled during operation.
FILLING OIL TANK:
WARNING: Removing the battery pack before
filling the oil tank.
1. Set chain saw on any suitable surface with Oil Filler Cap
(3) facing upward.
2. Clean area around the Oil Filler Cap with cloth and
unscrew the cap by turning it counter clockwise.
3. Add bar and chain oil until tank is full.
4. Avoid dirt or debris entering oil tank, refit Oil Filler Cap
(3) and tighten by turning clockwise until hand tight.
IMPORTANT: To allow venting of the oil tank,
small breather channels are provided between
the Oil Filler Cap and the strainer, to prevent
leakage, and ensure machine is left in a horizontal
position (Oil Filler Cap (6) uppermost) when not in use.
It is important to use bar and chain lubricant (not
provided) that is formulated to perform over a wide
temperature range with no dilution required. This can
be found at the location where you purchased this saw
or your local hardware store. Do not use dirty, used or
otherwise contaminated oils. Damage may occur to
the bar or chain. Use of non approved oil will void the
warranty.
Do not swallow. If swallowed, call a physician
immediately. Keep out of reach of children. Store away
from heat or open flame.
CHECKING THE AUTOMATIC OILER
Proper functioning of the automatic oiler can be checked
by running the chain saw and pointing the tip of the Guide
chain bar (6) towards a piece of cardboard or paper on
the ground. If an increasing oil pattern develops on the
cardboard, the automatic oiler is operating fine. If there
is no oil pattern, despite a full oil reservoir, contact Worx
customer service agent or Worx approved service agent.
CAUTION: Do not touch the ground with the
chain. Ensure safety clearance of 30cm.
OPERATION
1. BEFORE USING YOUR CORDLESS TOOL
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert or
allow metallic objects into your charger or battery pack
connections because of an electrical failure and hazard will
occur.
NOTE: Your battery pack is UNCHARGED and you must
charge once before use.
The battery charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another battery
charger.
EN