Cub Cadet SurePath Pro Z Serie Manual Del Operador página 21

Conducción automática cortadora con radio de giro cero
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

Manually steer
around obstacles
Brie y press SET LINE/ENGAGE
AUTO button to resume Auto Steer
Figure 3-9
NOTE: Do not hold the SET LINE/
ENGAGE AUTO button down when
resuming SurePath Auto Steer Mode.
Holding the button for 3 seconds or
more will reset the system, erasing the A
and B points previously set.
Automatic Shut Off or GPM Signal Loss
If the GPM loses signal, the mower will
return to manual mode. The following
sequence will occur:
1.
The Indicator/Warning Lights on
the Light Module will flash red
and the system will stop steering
the mower.
2.
The operator must resume control
of the steering wheel and turn it
slightly to either the right or left to
return to manual mode.
3.
Once GPS signal has been
reacquired, the Indicator/Warning
Lights will be solid green. Briefly
press the SET LINE/ENGAGE AUTO
button to resume SurePath Auto
Steer Mode.
WARNING
If the SurePath Auto Steer system malfunctions,
stop using the machine or disable the system and
have it repaired by an authorized servicing dealer
as soon as possible.
NOTE: If the SurePath Auto Steer system
malfunctions see Troubleshooting in
the Product Care section or contact an
authorized service provider.
Using the Mower Deck (SurePath Auto
Steer Mode)
WARNING
To avoid personal injury to you or others, always
use caution and be aware of your surroundings
when using the SurePath Auto Steer Mode. Stop the
machine immediately if anyone enters the area.
NOTE: Operator is always in control of
the mower's speed and braking.
1.
Use the deck lift pedal (a) to raise
the deck to its highest position,
place the clevis pin (b) attached to
the mower into the desired index
hole on the deck height index, then
slowly release the deck lift pedal (a).
Refer to Figure 3-6 on page 19.
2.
Mow across slopes, not up and
down. If mowing a slope, start at
bottom and work upward to ensure
turns are made uphill.
3.
To establish your mowing line
refer to Setting the Mowing Line
(SurePath Auto Steer Mode) section.
IMPORTANT! Setting the mowing line
automatically shifts mower to SurePath
Auto Steer Mode.
4.
Engage the PTO knob and move
the throttle control to the FAST
position.
5.
To move forward, slowly push the
forward drive pedal forward. The
SurePath Auto Steer system will
keep the mower aligned with the
preset mowing line.
NOTE: The speed of the mower
will affect cut quality of the lawn.
Mowing at full speed will adversely
affect a high quality cut lawn.
Control the ground speed with the
drive pedals.
6.
When approaching the other end
of the strip, release pressure on the
forward drive pedal slightly to slow
down before initiating a right or
left zero turn. Briefly press the right
or left turn button on the Operator
Control Panel. See Figure 3-10.
Left
Zero
Turn
Figure 3-10
WARNING
Do not attempt to make a turn at high speed when
using SurePath Auto Steer Mode. The system
will make smoother and more accurate turns at
lower speeds.
NOTE: Left and right turn buttons will
only function if SurePath Auto Steer
Mode has been activated.
NOTE: The SurePath Auto Steer system
will make smoother and more accurate
turns at lower speeds, and allow it
to more easily pick up and maintain
the signal for the next parallel line to
be followed.
7.
Make sure mower is realigned with
mowing line before accelerating.
8.
Repeat Steps 5-7 to continue
cutting parallel lines in SurePath
Auto Steer Mode.
IMPORTANT! To prevent rutting or
grooving of the turf, if possible, change
the direction that the strips are mowed
by approximately 45° for the next and
each subsequent mowing session.
Be careful when crossing gravel paths or driveways.
Disengage the PTO knob and raise the deck to the
highest/transport position before crossing.
NOTE: When stopping the mower
for any reason while on a grass
surface, always:
a.
Make sure the drive pedals
are in neutral.
b. Engage the parking brake.
c.
Shut engine off and remove
the key.
d. Doing so will minimize the
possibility of having your
lawn ''browned'' by hot
exhaust from your mower's
running engine.
9.
Release pressure on forward drive
pedal slightly before initiating right
or left zero turn.
10. Make sure mower is realigned with
mowing line before accelerating.
Disabling the SurePath Auto Steer System
To prevent unauthorized use, or if the
system malfunctions, the SurePath
Auto Steer system can be disabled by
removing the GPM fuse (labeled F5:GPM
Right
in the fuse box located under the
Zero
operator's seat).
Turn
Forced Striping
The SurePath Auto Steer system will
force side-by-side passes to be cut in
opposite directions. This setting can be
adjusted by contacting an authorized
service center.
Calibration
See Calibration in the Product Care
section for information regarding
calibrating the SurePath Auto
Steer system.
S
3 — c
ection
WARNING
& o
21
ontrolS
peration

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

Surepath pro z 960 s

Tabla de contenido