Power Supply - Makita HP2050 Manual De Instrucciones

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Speed
Capacities
No load speed
Blows per minute
Overall length
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
Intended use
The tool is intended for impact drilling in brick, concrete
and stone as well as for drilling without impact in wood,
metal, ceramic and plastic.

Power supply

The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-1:
Sound pressure level (L
Sound power level (L ) : 108 dB (A)
WA
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak- ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Concrete
Steel
Wood
) : 97 dB(A)
pA
HP2050 / HP2050F
High Low
20 mm
8 mm 13 mm
25 mm 40mm
-1
0 - 2,900 min 0 - 1,200 min
-1
0 - 58,000 min 0 - 24,000 min
362 mm
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-1:
Work mode: impact drilling into concrete
Vibration emission (a
Uncertainty (K) : 3.2 m/s
Work mode: drilling into metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
4 ENGLISH
HP2051 / HP2051F
High
- 20 mm
8 mm
25 mm
-1 -1
0 - 2,900 min 0 - 1,200 min
-1 -1
0 - 58,000 min 0 - 24,000 min
360 mm
2.5 kg
/II
2
) : 13.3 m/s
h,ID
2
2
) : 2.5 m/s or less
h,D
2
Low
-
13 mm
40 mm
-1
-1