Switch Action - Makita JV103D Manual De Instrucciones

Indicating the remaining battery capacity
Only for battery cartridges with the indicator
► Fig.2: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indicate the remain-
ing battery capacity. The indicator lamps light up for a few seconds.
Indicator lamps
Lighted
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Selecting the cutting action
► Fig.3: 1. Cutting action changing lever
This tool can be operated with an orbital or a straight
line (up and down) cutting action. The orbital cutting
action thrusts the jig saw blade forward on the cutting
stroke and greatly increases cutting speed.
To change the cutting action, just turn the cutting action
changing lever to the desired cutting action position. Refer
to the table to select the appropriate cutting action.
Position Cutting action
0 Straight line cutting
action
I Small orbit cutting
action
II Medium orbit
cutting action
III Large orbit cutting
action

Switch action

To turn on the tool, press the lock/unlock button. The tool
turns into the standby mode. To start the tool, pull the switch
trigger in the standby mode. To stop the tool, release the
switch trigger. The tool turns into the standby mode. To turn
off the tool, press the lock/unlock button in the standby mode.
For continuous operation, pull the switch trigger in the
standby mode, and then push in the lock on button. To stop
the tool, pull the switch trigger fully, and then release it.
► Fig.4: 1. Lock/unlock button 2. Lock on button
3. Switch trigger
Remaining
capacity
Off
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Applications
For cutting mild
steel, stainless
steel and plastics.
For clean cuts in
wood and plywood.
For cutting mild
steel, aluminum
and hard wood.
For cutting wood
and plywood.
For fast cutting in
aluminum and mild
steel.
For fast cutting in
wood and plywood.
NOTE: If the tool is left for 10 seconds without any
operation in the standby mode, the tool automatically
turns off and the lamp goes off.
NOTE: The lock/unlock button is not available while
the tool is operating.
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
To turn on the lamp, press the lock/unlock button. To
turn off the lamp, press the lock/unlock button again.
NOTICE:
When the tool is overheated, the lamp
flickers. Cool down the tool fully before operating
the tool again.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Speed adjusting dial
► Fig.5: 1. Speed adjusting dial
The tool speed can be adjusted by turning the speed
adjusting dial. You can get the highest speed at 5 and
the lowest speed at 1.
Refer to the table to select the proper speed for the
workpiece to be cut. However, the appropriate speed
may differ with the type or thickness of the workpiece. In
general, higher speeds will allow you to cut workpieces
faster but the service life of the blade will be reduced.
Workpiece
Wood
Mild steel
Stainless steel
Aluminum
Plastics
NOTICE:
When changing the speed dial from "5"
to "1", turn the dial counterclockwise. Do not turn
the dial clockwise forcibly.
Electronic function
The tool is equipped with the electronic functions for
easy operation.
• Soft start
The soft-start function minimizes start-up shock,
and makes the tool start smoothly.
• Soft no-load rotation
To reduce the vibration and align the jig saw blade
with the cutting line easily, the tool automatically
reduces the rotation speed until the tool starts cut-
ting the workpiece when the speed adjusting dial
is set at 2 or higher. Once the tool starts cutting
the workpiece, the tool speed reaches the preset
speed and keeps the speed until the tool stops.
NOTE: When the temperature is low, this function
may not be available.
10 ENGLISH
Number
4 - 5
3 - 5
3 - 4
3 - 5
1 - 4