Chicco Next 2 me air Manual Del Usuario página 23

ple: the during alignment of the crib to the bed.
In order to rotate the feet pull the rotation release button using
fig. 15).
itioned one hand and turn the feet of the crib inward (fig. 27).
WARNING: Use of the product is only permitted with beds
and/or mattresses with straight sides. Use of the product
with round beds and/or mattresses or water beds is not per-
mode). mitted.
WARNING: When the product is used in the "Bedside sleeper
YOUR
mode" (fixing to the bed, it should always be fitted to the long
ply with side of access to the bed. DO NOT fix the product to the head
or bottom of the bed.
be put
always MAINTENANCE ADVICE
raint of The crib and the mattress have a resistant fabric cover, which is
e firmly completely removable and washable.
ess sup- The removal/application activities should be carried out by
adults only. On a regular basis check the condition of the
Bedside product and the presence of any possible damage. In the
case of damage do not use it and keep it out of the reach
of children.
sheets,
crib. For washing of the fabrics, carefully comply with the instruc-
tions indicated on the label.
ing the For cleaning do not use solvents, abrasive products or aggres-
sive products.
button
her (fig. Hand wash in cold water
h sides,
e using Do not bleach
30° C
he Bed- Do not tumble dry
e height Do not iron
ts bed.
always Do not dry clean
ontain-
After each wash check the resistance of the fabric and of the
the crib stitching.
WARNING: During the removal and/or application of the lin-
sleeper ing, handle the fabric carefully in order to avoid accidental
can be damage or tears.
WARNING: the removal and/or application operations may
).
on both take a few minutes and should be carried out by an adult.
d above
MAKING THE BED
he par-
It is possible to unfasten the crib from the parents' bed in order
and fix to make the bed easily. Just unfasten the grey buckles located
eration below the fabric finish.
g of the To re-secure the crib to the parents' bed, pull once again the
istance belts to make sure the crib is properly and firmly secured to the
parents' bed. Pay attention to follow all the steps previously men-
nt's bed tioned in paragraph ''Bedside sleeper mode (Fixing to the bed)'' .
6). Car-
REMOVABLE LINING
her side,
with the
17. Remove the mattress and release the buttons on the lower
part of the fabric structure (fig. 28).
ure that 18. Press the buttons located on the legs' fastening point (fig.
side of 29) and pull the upper tubular structure upward, removing
there's the fabric lining from the legs (fig. 30). Perform these opera-
estored. tions on both sides.
ned on 19. Open the lateral zips on the window opening and press the
release buttons of the upper removable tubular structure
as explained in paragraph ''Bedside sleeper mode (Fixing to
the bed)'' . Then pull out the removable upper tubular struc-
t's bed, ture (fig. 31), paying attention not to damage the internal
parent's part of the lining.
erations 20. Open the zip located on the upper edge of the crib and
ble feet remove the fabric lining completely (fig. 32).
DISASSEMBLING THE CRIB
The crib can be fully disassembled in order to store it in the bag
supplied with the product. To disassemble the crib, repeat the
operations described in points 17-18 of paragraph ''Removable
lining'' . Then unfasten the central support structure by pressing
the fastening pins on both crib's legs (fig. 33).
WARRANTY
The product is guaranteed against any conformity defect in
normal conditions of use as provided for by the instructions
for use.
The warranty shall not therefore apply in the case of damages
caused by improper use, wear or accidental events.
For the duration of warranty on conformity defects please re-
fer to the specific provisions of national laws applicable in the
country of purchase, where provided.
23