Stanley Fatmax FME650 Traducción De Las Instrucciones Originales página 8

ENGLISH
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before cutting into walls, floors or ceilings, check for
the location of wiring and pipes.
Variable speed control (fig. H)
The variable speed control allows you to adapt the speed of
the tool to the application.
Set the variable speed dial (2) to the desired setting. At
u
setting 1 the tool will operate at low speed, 10,000 min-1.
At setting 6 the tool will operate at the maximum speed,
22,000 min-1.
Switching on and off (fig. I)
To switch the tool on, slide the on/off switch (1) forward
u
(position I).
To switch the tool off, slide the on/off switch (1) to the rear
u
(position O).
Cut guide (fig. F & J)
This feature allows you to more accurately track a marked
cut line.
To use the cut guide, insert the guide (13) as shown in
u
figure J into the front slot on the depth/cut guide block (8).
Adjust the length of the guide by pulling out or pushing
u
inward to achieve the desired cut depth.
Secure the guide in place by turning the depth/cut adjust-
u
ment knob (12) clockwise. To release the guide turn the
depth/cut adjustment knob anti-clockwise.
Depth guide (fig. F & K)
This feature allows you to precisely cut material at a specified
depth.
To use the depth guide, insert the guide (13) as shown in
u
figure K into the front slot on the depth/cut guide block (8).
Adjust the length of the guide by pulling out or pushing
u
inward to achieve the desired cut depth.
Secure the guide in place by turning the depth/cut adjust-
u
ment knob (12) clockwise. To release the guide turn the
depth/cut adjustment knob anti-clockwise.
Hints for optimum use
Always hold the tool securely. For precision work, hold the
u
tool near the front.
Clamp the workpiece whenever possible, especially when
u
using cutting blades.
Do not exert too much pressure on the tool.
u
Always use the appropriate type of attachment for the
u
workpiece material and type of cut.
Regularly check the condition of accessories. Replace
u
when necessary.
8
(Original instructions)
Mark the desired starting point.
u
Switch the tool on and slowly feed attachments into the
u
workpiece at the desired starting point.
Clamp a piece of plywood or soft wood to the back of the
u
workpiece and saw through the combination in order to
obtain a clear cut.
Do not force the cutting blade into the workpiece. Note
u
that cutting sheet metal will normally take more time than
sawing thicker wooden workpieces.
When cutting metal spread a thin film of oil along the cut-
u
ting line before cutting.
When sanding new layers of paint before applying another
u
layer, use extra fine grit.
On very uneven surfaces, or when removing layers of
u
paint, start with a coarse grit. On other surfaces, start with
a medium grit. In both cases, gradually change to a fine
grit for a smooth finish.
Consult your retailer for more information on available
u
accessories.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.