Functional Description - Makita TW0200 Manual De Instrucciones

ENGLISH
1 Switch trigger
2 Reversing switch lever
3 Socket
4 Anvil
5 O-ring
SPECIFICATIONS
Model
Capacities
Standard bolt .............................................. M10 – M16
High tensile bolt .......................................... M10 – M12
Square drive ...................................................... 12.7 mm
–1
No load speed (min ) ...................................... 0 – 2,200
Impacts per minute ........................................... 0 – 2,200
Max. fastening torque ........................................ 200 N•m
Overall length ..................................................... 251 mm
Net weight............................................................... 2.1 kg
Safety class ............................................................
• Due to our continuing program of research and devel- opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for fastening bolts and nuts.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety Hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES FOR TOOL
1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will also make exposed
metal parts of the tool "live" and shock the oper-
ator.
2. Wear ear protectors.
3. Check the socket carefully for wear, cracks or
damage before installation.
4. Hold the tool firmly.
5. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
6. The proper fastening torque may differ depend-
ing upon the kind or size of the bolt. Check the
torque with a torque wrench.
SAVE THESE INSTRUCTIONS.
Explanation of general view
6 Pin
7 Hook
8 Standard bolt
9 Fastening torque
10 Proper fastening torque

FUNCTIONAL DESCRIPTION

TW0200
CAUTION:
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
/II
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
Holding the tool
Hold the tool only by the handle when performing an
operation. Do not touch the metal part.
Reversing switch action (Fig. 2)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation.
ASSEMBLY
CAUTION:
ENB003-1
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Selecting correct socket
Always use the correct size socket for bolts and nuts. An
incorrect size socket will result in inaccurate and incon-
sistent fastening torque and/or damage to the bolt or nut.
Installing or removing socket
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the socket.
For socket without O-ring and pin (Fig. 3)
To install the socket, push it onto the anvil of the tool until
it locks into place.
To remove the socket, simply pull it off.
11 Fastening time
12 High tensile bolt
13 Limit mark
14 Brush holder cap
15 Screwdriver
5