Bosch Professional GOP 10,8 V-LI Manual Original página 16

OBJ_BUCH-630-007.book Page 16 Monday, January 7, 2013 10:59 AM
16 | English
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Removing the battery
To remove the battery 2, press the unlocking buttons 1 and
pull the battery out of the machine to the rear. Do not exert
any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
4 indicate the charge condition of the battery 2. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
To indicate the charge condition, press and hold button 3 of
the switched off machine.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
Changing the Tool
 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
 Wear protective gloves when changing application
tools/accessories. Contact with the application tool/ac-
cessoriy can lead to injuries.
Selecting the Application Tool/Accessory
Accessory
HCS wood seg-
ment saw blade*
BIM segment saw
blade*
HCS plunge cut
saw blades,
wood*
BIM plunge cut
saw blades,
metal*
BIM plunge cut
saw blade, wood
and metal*
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
1 609 92A 009 | (7.1.13)
Capacity
2/3
1/3
<1/3
Reserve
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
Mounting/Replacing the Application Tool/Accessory
If required, remove an already mounted application tool/ac-
cessory.
For removing the application tool/accessory, loosen the
screw 11 with the Allen key 12 and remove the application
tool/accessory.
Mount the requested application tool/accessory (e.g. plunge
cut saw blade 10) in such a manner on the tool holder 8 that
the offset faces downward (see illustration on the graphics
Material
page; marking on the application tool/accessory is readable
from above).
Wooden materials,
Turn the application tool/accessory to a position favourable
plastic
for the respective job, and allow it to engage into the cams of
Wooden materials,
the tool holder 8. 12 different positions are possible, each
plastic, non-ferrous
offset by 30°.
metals
For more intermediate positions, the adapter 13 (accessory)
Wooden materials,
can be used: Allow the adapter to engage with the smooth
plastic, gypsum
side onto the cams of the tool holder 8 (see illustration on the
and other soft ma-
graphics page). Position the application tool/accessory onto
terials
the adapter in any position.
Metal (e. g. unhard-
Fasten the application tool/accessory with bolt 11. Tighten
ened nails, screws,
the bolt with Allen key 12 until the spring washer of the bolt
smaller profiles),
faces flush against the application tool/accessory.
non-ferrous metals
 Check the tight seating of the application tool/accesso-
Wood, metal, non-
ry. Incorrect or not securely fastened application tools/ac-
ferrous metals
cessories can come loose during operation and pose a haz-
ard.
Mounting/Replacing a Sanding Sheet on the Sanding
Plate
The sanding plate 14 is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Accessory Material
HM-Riff segment Grouting joints,
saw blade* soft wall tiles,
glass-fibre reinforc-
es plastic and other
HM-Riff delta
abrasive materials
plate*
Scraper, rigid* Carpets, coverings
Scraper, flexible* Silicone and other
elastic materials
Base plate for Depends on sand-
sanding, series ing sheet
Delta 93 mm*
Bosch Power Tools