Metabo KPA 18 LTX 400 Manual De Instrucciones página 9

This also applies to dust from other materials such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
Vacuum or wash the protective clothing. Do not
blow, beat or brush.
Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws
related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
5. Overview
See page 2.
1 Front cap
2 Nozzle (for plastic bag) *
3 Tube
4 Half shell (for insertion of cartridges) *
5 Threaded ring for fastening the tube...
6 Button for unlocking the rack
(The toothed rod can only be retracted when
the button is pressed)
7 Toothed rod
8 Rod knob
9 Trigger switch for switching the device on and
off
10 Adjusting wheel for setting feed rate
11 Battery pack release button
12 Battery pack *
13 Capacity indicator button *
14 Capacity and signal indicator *
15 Plastic bag *
16 Extruder plate for plastic bags
17 Extruder plate for cartridges
18 Cartridge *
* not part of the delivery scope / depends on design
variant
6. Initial Operation
6.1 Battery pack
Charge the battery pack before use.
Recharge the battery pack if performance
diminishes.
The ideal storage temperature is between 10°C and
30°C.
Removal: Press the battery pack release button
(11) and remove battery pack (12).
Fitting: Slide in the battery pack (12) until it
engages .
Li-Ion battery packs "Li-Power, LiHD" have a
capacity and signal indicator (14):
- Press the button (13), the LEDs indicate the
charge level.
- The battery pack is almost flat and must be
recharged if one LED is flashing.
6.2 Fitting plastic bags
- Unscrew the front cap (1) from the tube (3).
- Push the rod knob (8) until the stop - this grants
access to the extruder plate (17).
Mount the extruder plate for plastic bags
(16) as shown ! See page 2, fig. A.
- Snip the top of the nozzle (2) as required for the
work to be carried out.
- Press the button (6) for unlocking the toothed rod
and pull the rod knob (8) backwards until the stop.
- Push the plastic bag (15) inside the tube (3).
- Trim the plastic bag (15) as recommended by the
plastic bag manufacturer.
- Insert the nozzle (2) in the front cap (1) and secure
the front cap (1).
- Now gently press the rod knob (8) to advance the
toothed rod until it comes in contact with the
plastic bag.
6.3 Fitting the cartridge
- Unscrew the front cap (1) from the tube (3).
- Push the rod knob (8) until the stop - this grants
access to the extruder plate (17).
Remove the extruder plate for plastic bags
(16) as shown ! See page 2, fig. B.
- Open the cartridge (18) as per the cartridge
manufacturer's instructions.
- Snip the top of the cartridge nozzle as required for
the work to be carried out.
- Press the button (6) for unlocking the toothed rod
and pull the rod knob (8) backwards until the stop.
- Push the cartridge (18) with the attached cartridge
nozzle into the tube (3) and secure the front cap
(1),
or
Insert the cartridge (18) with attached cartridge
nozzle into the half shell (4) (depends on design
variant / not part of the delivery scope).
ENGLISH en
9