Ordering Replacement Parts; Storage And Transport - EINHELL GE-SC 35/1 Li Manual De Instrucciones

•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
•
A worn out or damaged cutting unit should be
replaced by an authorised expert (see adress
on the warranty certificate).
•
Take care that all fastening elements (screws,
nuts, etc.) are firmly tightened, so that you
can work safely with the scarifier.
•
Store the scarifier in a dry place.
•
For longer life, all screw-fastened parts, such
as wheels and axles should be cleaned and
subsequently oiled.
•
Regular servicing of the scarifier not only
secures longer endurance and performance,
but also contributes to an accurate and simp-
le scarification of your lawn.
•
At the end of the season, carry out a general
check of the scarifier, and remove all residue
collected. Before the start of every season, it
is absolutely necessary to check the state of
the scarifier. Contact our Customer Service
(see address on the warranty certificate) if
repair work is necessary.
The push bar has a P position (Fig. 15) in order
to take up less space during storage. To adopt
this position you must loosen the quick-release
levers by approx. 3 turns to allow for the higher
fastening in the parking position. With the bar in
this position, the scarifi er can be stood in a corner
in minimum space (Fig. 23). When you return the
bar to the working position, remember to tighten
the quick-release levers again by 3 turns!
7.3 Changing the roller (see Figures 24-27)
Be sure to wear work gloves!
Only replace the roller with a genuine Einhell rol-
ler, as this will ensure top performance and safety
under all conditions.
To change the scarifying roller or the aerator roller
(Fig. 27b, Art. No.: 34.055.71), which is available
as an option, proceed as follows:
Remove the two Allen screws (Fig. 24 / Item A).
Lift the roller on this side and pull out in the direc-
tion of the arrow (Fig. 25).
Anl_GE_SC_35_1_Li_SPK7.indb 26 Anl_GE_SC_35_1_Li_SPK7.indb 26
GB
Now slide the new roller in the direction of the
arrow (Fig. 27a/27b) onto the square-ended drive
(Fig. 26 / Item A) and press into the holder (Fig.
27a).
Refasten the roller with the two Allen screws (Fig.
24 / Item A).
Apply grease to the square-ended drive from time
to time so that the rollers can be changed easily.
If the blade roller is set unfavorably, the outer
blade (Fig. 25/Item A) may be blocked by the
housing. In this case move the roller half a turn
forward!

7.4 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Replacement cutting unit Art. No.: 34.055.81

8. Storage and transport

Storage
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempera-
ture is between 5 and 30 °C. Store the machine in
its original packaging.
Transport
•
Switch the machine off and isolate it from the
power supply before transporting it.
•
Fit the shipping protectors, if any.
•
Protect the machine from damage and the
strong vibrations that can occur particularly
when transporting in vehicles.
•
Secure the machine against slipping and tip-
ping over.
- 26 -
29.07.2016 08:53:45 29.07.2016 08:53:45