IMG STAGELINE FM-1010 Manual De Instrucciones página 8

4 Filling Up Fog Fluid
GB
WARNING 1. While filling up fog fluid, the unit must
2. Never add flammable fluids of any
3. The unit is not splashproof. If fluid
1) Unscrew the tank cap (2).
2) Fill up the tank with fog fluid (
fluid is spilt, wipe it off immediately with a cloth so
that it will not get inside the unit.
3) Tightly close the tank.
4.1 Suitable fog fluid
The following fog fluids from "img Stage Line" suitable
for the unit are available in 5 litre containers:
Item Feature
NF-502L long fog effect
NF-502SL extra long fog effect
Only use the fluids listed above, otherwise no liability
will be accepted for correct operation.
The following scents by "img Stage Line" may be
added to the fog fluid:
Item Scent
NF-32 Vanilla
NF-62 Mixed fruit
NF-72 Strawberry
A bottle of scent (contents 25 ml) will be sufficient for
5 litres of fog fluid; higher quantities will clog the fog
machine.
5 Setting Up/Installing the Unit
G
The heat generated within the unit must be dissi-
pated by air circulation. Make sure that a minimum
space of 20 cm is provided around and above the
unit and that the air vents of the housing are not
covered.
G
During operation the fog output nozzle will become
very hot. Always ensure a minimum distance of
50 cm to easily flammable material or material sen-
sitive to heat.
G
Adjust the unit so that the hot fog stream will not
directly hit persons – risk of burns!
8
not be connected to the mains.
Always disconnect the mains plug
from the socket before filling up!
kind to the fog fluid! Explosion hazard!
gets inside the unit, it must be
cleaned and checked by skilled per-
sonnel before it is operated.
chapter 4.1). If any
Remove the complete packaging material. Make sure
that there are no packaging remnants at the fog output
nozzle.
Place the unit on a horizontal surface or mount it via
its bracket (1) [e. g. on a cross arm via a mounting clip].
For exact horizontal adjustment of the unit slightly
release the two screws (4) on both sides of the mount-
ing bracket, readjust the position of the unit, then
retighten the two screws.
WARNING Mount the unit safely and expertly. If the
Note: Fog machines will develop condensation around
the fog output nozzle. When selecting a mounting
place, take into account that moisture will accumulate
below the nozzle.
6 Operation
Order No.
38.1820
WARNING 1. The fog output nozzle will become
38.1830
Order No.
38.1780
1) Connect the remote control provided to the jack
38.1800
REMOTE CONTROL ONLY (7).
38.1810
2) Connect the fog machine via the mains cable (6) to
a mains socket (230 V~/50 Hz).
3) Prior to switching on the fog machine, check the
fluid level of the tank and fill up fog fluid, if required
( chapter 4).
4) Switch on the unit with the POWER switch (3): the
switch will light up. The fog machine will heat up for
approx. 4 minutes. While the unit is heating up, fog
output will not be possible yet.
Once the green LED (14) lights up, the heating
process of the fog machine is completed: The unit
is ready to emit fog (
5) After operation, switch off the fog machine with the
POWER switch (3).
Before transporting the unit, it must cool down
and the tank must be completely empty!
Note: Due to residual fluid in the fog machine, the unit
may still emit some fog after a fog output or after
switching off.
unit is installed at a place where people
may walk or sit under it, additionally
secure it (e. g. by a safety rope at the
bracket; fasten the safety rope in such a
way that, in the event of a fall, the max-
imum falling distance of the unit will not
exceed 20 cm).
very hot. Never touch it during opera-
tion or shortly afterwards. Risk of
burns!
2. The unit must be operated by adults
only; never leave it unattended.
3. Never operate the fog machine with-
out fog fluid, otherwise there will be
a fire hazard due to overheating.
Besides, the unit may be damaged.
chapters 6.1 – 6.3).