Idiomas disponibles
Idiomas disponibles
English
Protective Function
Overheat Protection
Tool Status
Motor stopped during
LED Lighting Status
Lighting Condition
Power mode: Light OFF
of the Display Lamp
Silent mode: Light ON
Cause
Countermeasure
Allow the unit to fully
cool down.
LED blinking should
stop approximately 10
seconds after releasing
the switch.
DISPOSING CHIPS
WARNING
When disposing chips, make sure that the tool is
switched off and that the battery is removed.
CAUTION
○ When cutting steel materials, make sure to empty
the waste material when the cuttings reach the mark.
(Fig. 26)
The heat of the cuttings may deform the saw cover.
○ Depending on the material being cut, the waste material
may retain heat. Do not touch the waste material or the
saw cover (A) and (B) with your bare hands.
NOTE
○ Collecting effi ciency will decrease if the tool is used
when the saw cover's interior is full of chips.
Make sure to dispose the chips before the interior of the
saw cover is full.
○ When disposing the chips, be careful not to spill the
chips into the motor or the battery mount.
○ Empty the inside of the saw cover when changing the
materials to be cut.
(1) Press the hook below the dust cover, open the dust cover
and dispose the chips inside the saw cover. (Fig. 26)
(2) Close the dust cover and secure it with the hook.
OR
(1) Point the saw cover downwards, loosen the wing nut,
remove saw cover (A) and dispose the chips collected
inside the saw cover. (Fig. 27)
(2) Attach the saw cover (A) and secure it with the wing nut.
NOTE
If any sawdust or other particles have collected on
the inside of the saw cover (B), please see page 18
"Cleaning the interior of the saw cover".
Overload Protection
Motor stopped during
operation
0.5 second
Power mode: Light OFF
Silent mode: Light ON
Motor at high
Motor is overloaded
temperature
Remove the cause of
the overload.
LED blinking should
stop approximately 10
seconds after releasing
the switch.
Table 3
Continual Heavy load
Protection 1
Motor speed declined
operation
during operation
0.1 second
Depends on the type of
LED light warning signal
Motor is continuously
If further overload
continues over a
long period of time,
Continual Heavy load
Protection 2 will be
triggered, and the unit
will stop operation.
Press the mode selector
switch approximately 10
seconds after releasing
the switch to cancel the
fl ashing and return to
Power mode display
lamp.
MAINTENANCE AND INSPECTION
1. Inspecting the saw blade
Since use of as dull saw blade will degrade effi ciency
and cause possible motor malfunction, sharpen or
replace the saw blade as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Motor unit maintenance
The motor winding is an important part of this tool. Avoid
damaging and be careful to avoid contact with cleaning
oil or water.
Dust or particle accumulation in the motor can result in
damage.
4. Inspecting and maintaining the lower guard
Always make sure that the lower guard moves smoothly.
In the event of any malfunction, immediately repair the
lower guard.
5. Cleaning the interior of the saw cover
Periodically check and clean to ensure that the saw
cover is clean of sawdust or other particles.
(1) Loosen the wing nut and remove the saw cover (A).
(Fig. 28)
NOTE
Depending on the shape of the saw blade being used,
the saw cover (B) cannot be removed. If this is the case,
reverse the order of the instructions for (2) and (3).
(2) Loosen the three screws with a Phillips head screwdriver
and remove saw cover (B). (Fig. 29)
(3) Remove the saw blade according to the instructions
listed under page 17 "Dismounting the saw blade".
(4) Remove chips from the inside of the saw cover, spindle,
washer and other areas. (Fig. 30)
18
Continual Heavy load
Motor stopped during
in use.
0.5 second
Continued operation
overloaded
despite Continual
Heavy load Protection 1
Remove the cause of
the overload and allow
the unit to cool down.
Press the mode selector
switch approximately 2
minutes after releasing
the switch to cancel
the fl ashing of the LED
light and display lamp.
Continue operation.
Protection 2
operation
0.1 second
0.1 second
warning
