Idiomas disponibles
Idiomas disponibles
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action
Adjusting the cutting depth
Cutting line
Switch operation
About the mode select function
Remaining battery indicator
Using the LED light
Attaching the guide (sold separately)
Attaching the hook
(*2)
(sold separately)
Removing and inserting the battery
Charging
Holding the tool
Connection with cleaner
(sold separately)
Dismounting the saw blade
Mounting the saw blade
(*3)
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
(*1) About the mode select function
Each time the mode selector switch is pushed, the
operation mode changes.
When Silent mode is selected, the Silent mode indicator
lamp lights up.
Figure
Page
9
3
10
3
11
4
12
4
(*1)
13
4
14
4
15
4
16
5
17
5
18
5
19
5
20
6
21
6
22
7
23-a
7
23-b
7
24
7
25
7
―
314
Silent mode reduces maximum motor RPM enabling
effi cient work with less noise.
If the load increases while the motor is operating in
Silent mode, it automatically changes to Power mode.
Additionally, if the load decreases again, it automatically
returns to Silent mode.
With power mode, the protection function activates to
reduce the number of revolutions whenever the unit is
continuously burdened with a heavy load.
Mode
Power
Silent
NOTE
○ The mode will only change after a battery is installed and
the switch is pulled once.
○ The current mode will be maintained even if the switch is
on/off , or the battery is removed/reinserted.
(*2) Attaching the Hook
The hook can be used to hang up the unit temporarily
during operations (Fig. 16).
CAUTION
The hook should never be used to hang the unit on your
person.
When using the hook, check to make sure that the main
unit will not slip and fall, or become unstable by the wind,
etc.
Never hang the unit from your belt or trousers as this
could cause accidents.
(*3)
After using the tipped saw blade, saw covers (A) and
(B) may become hot. Take caution when handling.
LED LIGHT WARNING SIGNALS
(Fig. 31)
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered during
operation, the LED light will blink as described in Table 3.
When any of the safeguard functions are triggered, follow
the instructions described under corrective action.
17
English
No-load speed
3600 min
-1
2400 min
-1
Fig. 31
