Idiomas disponibles
Idiomas disponibles
APPLICATIONS
Standard
For cutting soft steel materials*
accessories
For cutting stainless steel materials
Optional
accessories
For cutting wood materials
It is possible to cut aluminum. However, when doing so, apply cutting oil to the edge of the blade.
*
Optional accessories are subject to change without notice.
CAUTION
○ Do not connect with a cleaner when cutting steel materials.
○ Empty the inside of the saw cover when changing the materials to be cut.
○ Do not consecutively cut metal plates.
SPECIFICATIONS
1. Power tool
Model
Voltage
No-Load Speed
Cutting
Capacity
depth
Battery available for this tool*
Weight**
*
Existing
batteries
(BSL3660/3620/3626,
series, etc.) cannot be used with this tool.
** According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
Electronic control
○ Soft-start
○ Overload protection
This protection feature cuts off the power to the motor
in the event of overloading of motor or a conspicuous
reduction in rotational speed during operation.
When the overload protection feature has been
activated, the motor may stop.
In this case, release the tool switch and eliminate causes
of overloading.
After that you can use it again.
○ Overheat protection
This protection feature cuts off the power to the motor
and stops the power tool in the event of overheating of
motor during operation.
When the overheat protection feature has been
activated, the motor may stop.
In this case, release the tool switch and cool it down in a
few minutes.
After that you can use it again.
○ Continual heavy load protection
This protection function can result in a rotation decline
when a continuous heavy load is applied. Should the
heavy load continue, the motor may cease to operate.
○ Rotation speed changeover function (Power mode /
Silent mode)
Blades
CD3605DA
36 V
3600 min
Power mode
–1 (
2400 min
Silent mode
–1 (
90°
46 mm
Multi volt battery
2.8 kg (BSL36A18)
3.1 kg (BSL36B18)
BSL18xx
O For cutting various types of soft steel materials such as
steel pipe, steel channels ("C" channels, "L" angles etc.)
and aluminum sash.
Cannot be used for cutting tempered steel materials.
O For cutting stainless steeI materials such as round pipes,
etc.
O For cutting various type of wood materials.
(Power mode / Silent mode switch function)
Each press of the Mode Selector Switch changes the
operating mode. (Fig. 12)
Silent mode reduces maximum motor RPM enabling
effi cient work with less noise.
The Silent Mode Indicator Lamp lights in Silent mode.
When the load increases during Silent mode, the tool will
automatically switch to Power mode and revert back to
)
Silent mode when the load decreases.
)
In Power mode, no change is made to Silent mode even
when the load decreases.
NOTE
○ To enable mode changes, pull the switch once after
installing the battery.
○ Do not give a strong shock to the switch panel or break it.
It may lead to a trouble.
2. Battery
Model
Voltage
Battery capacity
Available cordless
products**
Available charger
*
The tool itself will automatically switch over.
** Please see our general catalogue for details.
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the charge indicator lamp will blink in red (At 1- second
intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 18 (on page 5).
3. Charging
When inserting a battery in the charger, the charge
indicator lamp will blink in blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table 1, according to the condition of the
charger or the rechargeable battery.
15
English
Uses
BSL36A18
36 V / 18 V (Automatic Switching*)
2.5 Ah / 5.0 Ah
(Automatic Switching*)
Multi volt series, 18 V product
Sliding charger for lithium ion
batteries
