Tabla de contenido
Idiomas disponibles
Idiomas disponibles
2. Using a square, check to see if the fence is at
90 degrees to the table.
3. If the fence is not at 90 degrees, loosen nut
(D)and adjust the stop screw (B) until the fence
is at 90 degrees to the table. Retighten nut (D).
4. Tilt the fence in-
ward until it hits the
45 degree in stop nut
(Fig.19-E).
5. Using a combina-
tion
square,
check
to see if the fence is
indeed tilted in at 45
degrees (Fig.20).
6. If an adjustment is necessary, tighten or
loosen the stop nut (E) until the fence is at 45
degrees.
7. Tilt the fence outward to 45 degrees. To do
this you will have to flip the 90 degree stop
(Fig.16-C) out of the way so that it faces to-
wards the infeed table.
8. Using a combina-
tion
square,
check
to see if the fence is
tilted at 45 degrees
(Fig.21).
9. If an adjustment is necessary, loosen the hex
nut located on the 45 degree stop and adjust
the stop screw until the fence is at 45 degrees
to the table.
CHANGING MOTOR VOLTAGE
WARNING: Make sure that the jointer is dis-
connected from the power source. Have a certi-
fied electrician make all electrical connections.
The motor supplied with the jointer is a dual
voltage 120/220 volt, single phase motor. The
motor is wired from the factory for 120 volt
operation. To change to 220 volt operation
for your jointer, proceed with the following
instructions. It is also necessary to replace the
120 volt plug, supplied with the jointer, with a
UL/CAS listed plug (not included) suitable for
220 volts and the rated current of the motor.
The jointer with a 220 volt plug should only be
connected to an outlet having the same con-
figuration as the plug. No adapter is available
or should be used with the 220 volt plug.
1. Make sure the switch is "OFF" and discon-
nect power cord from power source.
26
Fig.20
Fig.21
2. Unscrew the six screws that fasten the access
panel to the base of the jointer and remove
access panel.
3. If motor tag states
that it is dual voltage
remove Junction box
cover
(Fig.22-A)
on
motor.
4. Using wiring dia-
gram on inside of
junction
box
cover,
reconnect motor leads for 220-volt operation.
5. Replace junction box cover and reattach
panel removed on step 2.
6. Replace the 120 volt plug with a plug rated
for 220 volt operation.
7. The ON/OFF switch is 4-pole and does not
need Modified.
OPERATION INSTRUCTIONS
IMPORTANT: Permit only trained and autho-
rized employees to operate equipment. Inspect
and maintain guards, safety devices and start/
stop controls. Instruct, train and supervise the
safe method of work.
WARNING: Serious personal injury may occur
if normal safety precautions are overlooked or
ignored. Accidents are frequently caused by
lack of familiarity or failure to pay attention.
Obtain advice from supervisor, instructor, or
another qualified individual who is familiar
with the machine and its operations.
Every work area is different. Always consider
safety first, as it applies to your work area.
Use any machine with respect and caution.
Failure to do so could result in serious personal
injury and damage to the machine.
STOP using the machine, if at any time you
experience difficulties in performing any op-
eration. Contact your supervisor, instructor or
machine service center immediately.
ON/OFF SWITCH
The START / STOP switch
assembly is located above
the infeed table. To turn
the jointer "ON". push
the green start button
(Fig.23-A).
A
Fig.22
B
A
C
Fig.23
Tabla de contenido
