Caution - Fimer KING 350 Manual De Instrucciones

WARNING SYMBOLS
DANGER
(Indicating a hazard that could cause injury or damage)
ELECTRIC SHOCK
(Indicating the danger of electric shock)
DANGER
OF FIRE.
Indicating that eye protection is required to avoid
burns and eye damage.
HOT SURFACE
Do not touch the surface
HOT SLAG
Indicating the risk of being burned by hot slag
EYE PROTECTION
Indicating that eye protection is required to avoid flying debris
READ THE INSTRUCTION MANUAL

CAUTION

CAUTION
SAFETY WARNINGS
EXTERNAL ACCESSIBLE LIVE PARTS
UNDER VOLTAGE
(Negative and Positive Terminal Fast-Connect Plug)
WARNING OF HIGH VOLTAGE ELECTRIC SHOCK INJURY
This equipment is designed solely for industrial or pro-
fessional use. As such, only experienced or fully-trained
people should use the equipment.
The user and/or owner is responsible for ensuring inexperienced
personnel does not have access to the equipment.
The constructor declines all responsibility for injury or
damage caused by inexperienced, improper or neglect-
ful use of its equipment.
A workman must look after his tools carefully ! Remember that
any tool or equipment can become a hazard if it is not looked
after properly.
Equipment in a state of disrepair or neglect can be dangerous. If it does
not operate properly or overheats, the electricity supply should be remo-
ved immediately and the unit should be returned to the supplier for repair.
Read this manual carefully before using your Welder.
You can then do a better and safer job.
By reading this manual you will learn more about the
possibilities, limitations and potential dangers of welding.
Retain this manual for the entire life of the equipment. It should be
kept within the operator's reach at all times.
The safety information contained in this manual is a guide to
ensure you are not subjected to unnecessary risks. However,
the operator must be competent and careful at all times.
All equipment connected to electric power supplies can be dan-
gerous if the manufacturers instructions are not read and obser-
ved. Read, understand and observe these safety instructions
to reduce the risk of death or injury from electric shock. Ensure that
even bystanders are aware of, and understand, the dangers that
exist in the welding area.
Fires and explosions can seriously injure or cause dama-
ge ! Read, understand and observe all safety warnings
to reduce the risk of death or injury from fire or explo-
sion. Pay particular attention to the fact that even bystanders should
be aware of, and understand, the dangers existing in the welding area.
Remember that welding, by nature, produces sparks, hot spatter, mol-
ten metal drops, hot slag and hot metal parts that can cause fires, can
burn skin and damage eyes.
2
WARNING SYMBOLS
WARNING SYMBOLS
DANGER EXPLOSIONE RISK
Indicating the risk of explosion in the event of improper handling
or maintenance of compressed gas cylinders or regulators
FIRE
PRECAUTIONS
IMPORTANT INFORMATION
Indicating the precautions to be taken when installing and
using the unit.
DISPOSAL
INFORMATION
INSTALLATION
INSTRUCTIONS
OPERATING
INSTRUCTIONS
UNPACKING
INSTRUCTIONS
SUITABLE FOR ENVIRONMENT WITH INCREASED
HAZARD OF ELECTRIC SHOCK
Arc rays can damage your eyes and burn your skin !
Read, understand and observe all safety warnings to
avoid damage from arc rays. Pay particular attention
to the fact that even bystanders should be aware of, and understand,
the dangers existing in the welding area. Wear a protective mask
and make sure bystanders do the same.
Fumes, toxic gases and vapours can be harmful ! Read,
understand and observe all safety warnings to avoid harm
from toxic welding gases. Pay particular attention to the fact that even
bystanders should be aware of, and understand, the dangers.
Carelessness while using or maintaining the compres-
sed gas cylinders or regulators can injure or kill the
operator and/or bystanders ! Read, understand and observe all safety
warnings to avoid the dangers of compressed gas. Pay particular
attention to the fact that even bystanders should be aware of, and
understand, the dangers.
HIGH VOLTAGE
The unit carries potentially lethal voltage.
The high voltage areas of the equipment have been segregated
and can be reached only by using tools that are not provided with the
Welder.
All maintenance or repair operations requiring access to such areas may
only be performed by constructor-trained technicians.
FOREIGN OBJECTS
Never block the air vents with foreign objects and avoid
any contact with liquids. Clean using just a dry cloth. The-
se safety precautions apply even when the unit is switched off.
WEIGHT LOADS
The upper part of the Welder was not designed to with-
stand heavy loads. Never stand on the unit.
CABLE GAUGES
Check that all cables are appropriately gauged for
the input power required by your specific Welder.
This precaution applies also to extension cables, if used. All extension
cables must be straight. Coiled cables can overheat, becoming dange-
rous. Twisted or coiled cables can also cause Welder malfunction.