Assembly Instructions 630 - Teuco 630 Instrucciones De Montaje

GB
The product must be installed exactly as supplied by Teuco, otherwise warranty will be invalidated.
The directions for installation must be observed to the letter, as must those concerning recommended materials and
the accessories supplied with the product.
Electrical connections must be carried out in compliance with national safety regulations, as indicated in the
preinstallation data sheet. This manual constitutes an integral part of the product and must be kept for future reference.
Data and specifications indicated are not binding on the company: Teuco SpA reserves the right to make such
changes as are deemed appropriate without prior notice and without any obligation to update.
The product has been designed for domestic use. In case of heavy-duty use, as well as the technical and safety
guidelines envisaged by Teuco, it is also necessary to guarantee full compliance with specific legislation for equipment, safety and the treatment of water, as in force in the country where the Teuco minipool is being used.
The contractor/owner is responsible for verifying and ensuring compliance with local regulations prior to installation.
1
TECHNICAL SPECIFICATIONS
The 630 pool comprises:
- SPA-PACK: includes the whirlpool pumps, the filtration
system (sand or cartridge) and the water heating system
(heat exchanger or electric heater).
- OVErFLOW TANK
Collects the water displaced when one or more bathers
step into the pool.
- MiNiPOOL: the actual pool must be connected by
pipelines to the Spa-pack, the overflow tank and the
drain.
COMPONENTS
indicated below are the various components and
connections needed installation of the system (figures 11).
Minipool and pipelines
N) spill edge gutter and grating
K) filtration pump delivery
L) whirlpool pump suction
r) whirlpool pump delivery
M) overflow tank flow and return
Spa-pack
1) electrical panel
2) electric heater or heat exchanger
3) whirlpool pumps
4) filtration pump
5) sand filter with valve W - cartridge filter
6) filter drain (sand version)
Overflow tank
7) overflow
8) filler solenoid valve
9) level sensors
10) water load anti-reflux safety
11) tank drain
C) drain gully
20
INSTRUCTIONS FOR INSTALLATION
WARNINGS
2 6
INSTALLATION
Minipool
The minipool is designed specifically for built-in type
installation, with the edge exactly at floor level; refer to the
dimensions indicated in the drawings when preparing the
pit.
(N.B given that dimensional specifications may be
subject to slight variations, check all measurements
before proceeding with installation).
The pit for the built-in minipool should be cast in concrete,
observing the dimensions indicated in the drawing and
making certain that the structure is perfectly level. The
plinth or slab directly supporting the minipool must be able
to support the load (see table on page 2).
Leave a void (A) at least 40 cm wide all round the minipool
to ensure sufficient freedom of access to the plumbing and
electrical equipment installed beneath the tub.
The void must be covered with removable grate decking
carried on suitably sturdy supports and affording air
passages of at least 0.3 m
adequately ventilated.
Provide channels and a drain outlet (S) at the bottom of the
pit so that water will not collect and stagnate.
Plan the routes, preparing ditches and ducts where
necessary, for the water pipelines and electrical wiring
connecting the pool to the Spa-pack, the overflow tank and
the drain gully (C); the pipelines are as indicated in this
manual (figures 11), and must be positioned in such a way
as to avoid any possibility of siphoning in the system.
Spa pack
The Spa-pack must be installed at a distance of less
than 8 metres from the minipool: the shorter the
pipelines can be made, the lower the pressure losses, and
the better the general performance both of the filtration
system and of the whirlpool system. in any event, the Spa-
pack must be positioned at a height either level with or
lower than the overflow tank.
it is advisable to avoid bends as far as possible, and
preferably to use flexible plastic pipe (PVC). The pipe
utilized must be able to withstand pressure up to 3 bar and
temperature up to 60 °C.
Where flexible pipe is used, make certain the properties of
the material are such as to withstand negative pressure
generated on the suction side of the pumps.
The piping connecting the drainage channels in Art. 630
uses 75 mm diameter pipes.
75-80 mm diameter adaptors are fitted to the ends of the
two drainage channels to make it possible to couple the 80
mm piping for connection to the spa-pack.
Art. 630
overall so that the pit will be
2