General Power Tool Safety Warnings - Makita BHS630 Manual De Instrucciones

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 36
ENGLISH (Original instructions)
1.
Red indicator
2.
Button
3.
Battery cartridge
4.
Star marking
5.
Lever
6.
Wing screw
7.
Cutting line
8.
45° position
9.
0° position
10. Screw
11. Top guide
SPECIFICATIONS
Blade diameter
Max. Cutting depth
No load speed (min
Overall length
Rated voltage
• Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
CORDLESS CIRCULAR SAW
SAFETY WARNINGS
1.
DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on
auxiliary handle, or motor housing. If both hands
are holding the saw, they cannot be cut by the blade.
2. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the
workpiece.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
6
Explanation of general view
12. Switch trigger
13. Lock-off lever
14. Light
15. Shaft lock
16. Hex wrench
17. Loosen
18. Hex bolt
19. Outer flange
20. Saw blade
21. Inner flange
22. Dust nozzle
Model
at 90°
at 45°
-1
)
Net weight
4. Never hold piece being cut in your hands or
ENE028-1
across your leg. Secure the workpiece to a stable
platform. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
A typical illustration of proper hand support and
workpiece support. (Fig. 1)
GEA010-1
5. Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting tool may contact hidden wiring. Contact
with a "live" wire will also make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
6. When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
7. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the saw
GEB061-3
will run eccentrically, causing loss of control.
8. Never use damaged or incorrect blade washers or
bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
9. Kickback causes and related warnings:
- kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw
to lift up and out of the workpiece toward the
operator;
- when the blade is pinched or bound tightly by the
kerf closing down, the blade stalls and the motor
23. Thumb screw
24. Hose
25. Vacuum cleaner
26. Clamp lever
27. Rip fence (Guide rule)
28. Adjusting screw
29. Triangular rule
30. Base
31. Limit mark
32. Brush holder cap
33. Screwdriver
BHS630
165 mm
66 mm
46 mm
3,100
346 mm
3.5 kg
D.C. 18V
Tabla de contenido
loading

Este manual también es adecuado para:

Bhs630z

Tabla de contenido