Normal Operation - Jacuzzi ALLUSION 6636 Manual De Instalación Y Operación

WHIRLPOOL CONTROL PANEL OPERATION
Electronic Control Panel Operation
General Functions
The bath is equipped with a water level sensor. When the
water level is below the sensor, the pump/motor can not be
activated. If the ON/OFF pump/motor button is pressed at
this time, the display will show "LO" for 5 seconds and the
low level indicator will come on. When the water goes above
the water level sensor, the low water level indicator will go
OFF and the pump/motor can then be activated. If the water
level drops below the level sensor, the pump/motor will shut
off. To restart the pump/motor after the water level goes
above the level sensor, the ON/OFF button must be pressed.
The pump/motor will automatically shut off 30 minutes after
the pump/motor was turned on.
NOTE:
Low water level indicator LED is OFF when the bath is
full: Ensure the water level sensor located inside the bath
(as shown below) is free of any soap or dirt buildup. If sensor
is clean, this function can be overridden by holding the ON/
OFF button for approximately 3 seconds and then the pump/
motor will turn ON. The override feature is cancelled once
the pump/motor has been turned off.
On initial power up the display will show 188 and all bubbles
will come on. The system will then calibrate the air valves. If
one valve is not detected in about 30 seconds, the next valve
will be calibrated. If this valve is not detected after about 30
seconds the display will go blank and the following functions
can be used: pump/motor ON/OFF, Temperature readout
and Light.
If the system control is not responding: Power down the
system by either unplugging the unit or shutting OFF the
power at the house breaker panel. Wait 15 seconds then
power back up. Retry the system by activating the feature
that was not responding.
TYPICAL BATH FITTINGS
FULLY
FULLY
ADJUSTABLE
ADJUSTABLE
SIDE JETS
BACK JETS
AIR JETS
SUCTION COVER
Jacuzzi Whirlpool Bath© BR28000A 3/05
WHIRLPOOL CONTROL PANEL
WATER LEVEL SENSOR
AIR BATH
LIGHT
CONTROL PANEL
DRAIN/OVERFLOW
#1 AIR FLOW INCREASE
LOW WATER
LEVEL INDICATOR
LED DISPLAY
#1 AIR FLOW
DECREASE

Normal Operation

On/Off Pump/Motor
Pressing this button will turn ON the pump/motor. Pressing
a second time will turn OFF the pump/motor.
#1 Air Flow Increase
Pressing this button will increase air flow to one set of jets.
The air flow can be adjusted from no air to maximum air.
The display will show up to four bubble icons flashing ON
and OFF. Each additional icon indicates more air flow.
#1 Air Flow Decrease
Pressing this button will decrease air flow from the one set of
jets. The air flow can be adjusted from maximum air to no
air. The display will show fewer bubble icons flashing ON
and OFF indicating less air flow. No flashing icon indicates
that the air has been turned OFF.
#2 Air Flow Increase
Pressing this button will have the same effect as #1 Air Flow
Increase for the other set of jets.
#2 Air Flow Decrease
Pressing this button will be the same as #1 Air Flow Decrease
for the other set of jets.
WavePulse ™
Pressing this button will first turn OFF air to both sets of jets
followed by ON and OFF air induction to first one side of the
bath and then to the other side. This will continue until the
wave button is pushed a second time, which stops the wave
action.
Bath Light ON/OFF
Pressing this button will turn ON the bath light(s). The light(s)
will come ON displaying the White colored light. Pressing a
second time will turn all light(s) OFF. (Use the "Light Color
Cycle" button to turn ON the color lights.)
Light Color Cycle
Pressing this button will turn ON the colored light(s) to the
"favorite" light (default is blue). Pressing this button again
will begin the light(s) cycling through each of the available
colors. This will continue until the Light Color Cycle button is
pushed again, which stops the light cycling action on the cur-
rent color. Press the button again and you will begin the
Light Color Cycle again.
To create a new "favorite" color: Allow the lights to rotate to
the new "favorite" light color. Stop the cycling on that color.
Press and hold down the button for three seconds (the light
will then blink to confirm the new "favorite").
Low Water Level Indicator
The Red water level indicator LED is OFF when tub is filled
above the water level sensor and pump button is pushed. If
you press the Pump button and the water level is below the
sensor the indicator LED will flash 4 times and the display
will read LO and the pump will not come ON.
10
LIGHT COLOR CYCLE
WAVE PULSE
#2 AIR FLOW
INCREASE
#2 AIR FLOW
DECREASE
ON/OFF
PUMP MOTOR
BATH LIGHT ON/OFF
(with the bath filled to the proper level)