Tabla de contenido
GETTING STARTED
Congratulations on your purchase of a Hayward ColorLogic LED Light.
Welcome to a more colorful world brought to you by Hayward and
Chromacore, (R) patented technology that generates colored light and
effects using a microprocessor to control red, green, and blue LED's.
Your Hayward ColorLogic underwater pool or spa light has these
features:
1. Long-lasting LED's (light-emitting diodes) which can last up to 10
times longer than current incandescent, halogen, or metalhalide
pool and spa lights.
2. Multicolor capability without any color wheels or moving parts to
wear out.
3. Multicolor program capability which allows you to select any one
of 12 different programs, 5 fixed colors, and 7 color shows.
4. Low power consumption. Uses approximately half of the power
needed for an ordinary 100 watt light.
OPERATING THE LIGHT
Your Hayward ColorLogic light is operated through power-cycling: a
method of changing modes which requires no special controller or
interface. To activate the light, simply turn on the switch. To deactivate
the light, turn off the switch. To advance to the next program, turn the
switch off, then back on within 10 seconds. Whenever the light has
been off for over 60 seconds, and is first turned on, it will come on to
white for 15 seconds for quick clear view of your pool, then go to the
last fixed color or color show it was running.
LIGHT SYNCHRONIZATION
If your pool or spa has multiple Hayward ColorLogic LED lights, they
may be operated independently, or they can be easily synchronized so
they will all display the same colors and shows at the same time. For
light synchronization, all lights must be wired to the same switch. Once
installed, all lights should be automatically synchronized, however, if
they get out of sync, they can be re-synchronized easily. To re-syn-
chronize your lights, turn the switch on, then back off, then wait be-
tween 11 and 14 seconds and turn the switch back on. When the lights
come back on, they should enter program #1, and be synchronized.
Hayward (R) is a registered trademark and ColorLogic (TM) is
trademark of Hayward Pool Products, Inc.
Chromacore (R) is a registered trademark of Color Kinetics, Inc.
All Rights Reserved.
Patents 6,016,038 and 6,150,774
European Patent 1,016,062
Other patents pending.
© 2004 Hayward Pool Products, Inc.
OPERATING INSTRUCTIONS
PROGRAMS
Your Hayward ColorLogic light has the capability to display 12 differ-
ent programs. These programs are advanced using power-
cycling. The programs are:
1. Show - Voodoo Lounge - Fast Color Wash
2. Fixed - Deep Blue Sea
3. Fixed - Afternoon Skies
4. Fixed - Emerald
5. Fixed - Sangria
6. Fixed - Cloud White
7. Show - Twilight - Slow Color Wash
8. Show - Tranquility - Blue/Cyan/White Fade
9. Show - Gemstone - Blue/Green/Magenta Fade
10. Show - USA! - Red/White/Blue Switch
11. Show - Mardi Gras - Fast Random Fade
12. Show - Cool Cabaret - Fast Random Fade
TROUBLESHOOTING
If you have a problem with your Hayward ColorLogic light, please try
the following tips before calling for service:
PROBLEM: Light will not advance to the next show when it is power-
cycled (turned "off" and then back "on").
SOLUTION: Do not power-cycle the switch rapidly, leave it off for at
least 1 second before turning it back on.
PROBLEM: Light goes to white whenever it is power-cycled (turned
"off" and then back "on").
SOLUTION: Be sure that you power-cycle the light for less than 10
seconds.
PROBLEM: Multiple lights are not correctly synchronized.
SOLUTION: Follow the steps in these instructions to re-synchronize
the lights.
PROBLEM: Light will not come on.
SOLUTION: Check ground fault and reset if necessary.
PROBLEM: Light will not come on or cycles on and off.
SOLUTION: Automatic thermal switch may be cycling due to excessive
temperatures. Check pool or spa water temperature.
PROBLEM: Light does not function properly, or does not function at all.
SOLUTION: Verify that your pool/spa controller is not "dimming" the
light.
ENGLISH
Tabla de contenido
