stayer SC250W Manual De Instrucciones página 53

SC2600W
Kind of cut
90º
45º Inclinado
45º-45º Compuesto
45º recto
Mesa superior
SCC255
Kind of cut
90º
45º Inclinado
45º-45º Compuesto
45º recto
Mesa superior
12. General instructions for use
Warning!
1. Do NOT use the machine if it is in a bad condition or
lacks parts including the prescribed upper guards
(the illustrations of the present manual may be used
as an orientative guide). Unplug it, remove it from the
working area and immediately send it to an authorized
technical service.
2.Know and comply with all safety measures before you
start the machine.
3. Obligatory used of aspiration particle system when
cutting the wood.
Starting and stopping the machine
IMAGES A B N
Information
1.The machine is provided with a locking button 3 for
starting allowing the motor to run without needing to
push switch 2 permanently.
2.The equipment is provided with a safety module
protecting it against unexpected starts. If, whilst
the machine is running, the supply of electrical
power should cease, the machine will not start after
reestablishment thereof. To release the protection
push the starting button 2 twice.
3.All models are single speed.
Warnings!
1.Avoid locking whenever possible (button 3).
2.Never leave running machine unattended.
3.Never start the machine with locked disk and, before
starting a cut, always wait until the cutting disk has
reached its maximum speed.
4.Before stopping the machine the disk must be clear and
be rotating freely.
Limit of the workpiece size
in mm
55x125
45x125
45x80
55x80
0-42
Limit of the workpiece size
in mm
70x110
40x90
35x50 (Izq) / 40x90 (Dcha)
50x100
0-40
ENGLISH
53
Starting with the manual switch
1.Push switch 2 to actuate the motor.
Stopping the machine when actuated with the manual
switch
1. Stop pushing switch 2.
Starting with locking
1.Push switch 2.
2.Push locking button 3 whilst keeping switch 2 pushed.
3.Release switch 2.
Stopping the machine when actuated with locking
Push switch 2 briefly.
Use of the lower cutting table
Warning!
1.At those models that are provided with an upper cutting
table, the risk of accidents due to a contact with the cutting
disk appearing at the upper table.
For your own safety, carry out the following preparation
before working with the lower table.
2.It is mandatory to carry out any settings with the cable
unplugged.
Safety setting of the upper cutting table for
cutting operations with the lower table
IMAGES A B O P
Information
This chapter is applicable to models provided with an
upper table: SC250WPRO, SC265W, SC291W SC2500W,
SC2600W and SLL265W.
1.Loosen the screw of the shaft and release lock (38) of
the guard of the upper cutting table 25.
2.Loosen the 3 wing nuts 24 that regulate the height of the
upper table.
3.Raise upper table 25 smoothly pulling upwards until
abutment.
4.Firmly tighten the 3 wing nuts 24.
5.Firmly tighten the screws of the guard of the upper
cutting table 25.
Cutting operation with the lower cutting table
Warning!
1.Respect the limits regarding the size and material of the
workpiece.
2.Use clamps to fasten the workpiece whenever possible.
3.Never lock the motor power switch when working with
the lower cutting table.
The present electrical machine is capable of carrying out
the following kinds of cuts on the lower table:
1.Inclined horizontal cut with a range of 0º to +- 45º.
2.Inclined vertical cut with a range of 0º to 45º.
3.Combinations of the horizontal and vertical ranges (for
example as an abrasive cutoff machine with straight
cuts horizontally at 0º and vertically at 0º).
53