Tabla de contenido
DASHBOARD DESCRIPTION (FIG.1)
1. Starting switch
Controls activation of all the electric system components.
Pos. 0 = electric system off
Pos.1 = electric system on
2. Multi-function display
When the electric system is activated the display shows the washing
programme and the pre-set calibrations as described below:
1. (RCM 01) with standard programme
or:
- (RCM 02 ) with programme for pump kit and detergent (optional).
- (RCM 03) with programme for pump kit without detergent (optional).
2. (PB 24) calibration programme for lead-acid batteries (standard
confi guration), or: (GE 24) calibration programme for gel batteries
(optional confi guration) with 24V.
3. (000, 001,..etc.) indicates calibration settings and washer-dryer fun-
ctions update.
4. (0-100) the value shown indicates the charging status of batteries.
In all the versions the working hours can be shown by pushing the button 6.
Additionally, the display shows the machine faults. For descriptions see
"DIAGNOSTICS - DISPLAY page 64".
!
Caution!
For BATTERY Confi guration see chapter "Optional | Machine Con-
fi guration WITH LEAD-ACID AND/OR GEL BATTERIES".
!
Caution!
DO NOT modify the described programs or settings. For informa-
tions contact the RCM service center.
3. Drive speed adjusting potentiometer
Used to set the type of speed to be used during travel or work.
-
Turn to the "tortoise" symbol to set the machine at a low speed
for thorough cleaning.
-
Turn to the "hare" symbol to set the machine at a high speed
for travel between jobs.
-
Turn to between the "tortoise and hare" symbols to set the
machine at a speed (and cleaning level) between the two ex-
tremes.
4. Drive control levers
The levers control the travel of the machine.
A= Forwards, R= Reverse
5. Emergency stop push-button
Cuts out the contacts for all the controls simultaneously.
If an emergency occurs, press this button. To restore operation, pull
up the button.
6. Commutation push-button battery status || hourmeter
Push the button to show on the display 2 the working hours or the
battery status charge.
7. Vacuum system on || off push-button
Switches on || off the vacuum motor.
The button has a led. When switching on the vacuum, the led blinks.
In normal working conditions the led is on. In case of over-absortion or
any other faults for the vacuum motor, the led blinks.
!
Caution!
The switching off the vacuum system is retarded by two seconds
to permit the completely emptying of the vacuum hose.
8. Push-button for "brush standard pressure", lowe-
ring and rotation.
Controls the lowering, rotation and "brush (standard) pressure" on the fl oor.
The button has a led. When switching on the brush button, the led blin-
ks. In normal working conditions the led is on. In case of over-absortion
or any other faults for the vacuum motor, the led blinks.
9. 2nd "brush pressure" push-button
Controls the max. "brush pressure" on the fl oor.
!
Caution!
If necessary, use this function for a stronger
!
Caution!
This function can be activated just when brush basement is lowe-
red and when machine is moving forward.
10. Brush water (fl ow) indicator (optional)
Shows the brush water fl ow setted by the push-buttons 12.
11. Detergent percentage setting push-button (optional)
Used to set up the program of dilution of the detergent on the brushes.
The choice of program depends of the dirt on the fl oor.
!
Caution!
This function is activated by the program (RCM 02) only.
This function controls three programs displayed in this way
- det.0 (pump switched off)
- det.1 (1% detergent diluted)
- det.2 (2% detergent diluted)
- det.3 (4% detergent diluted)
Push the button once to show on the display the current percentage
of detergent.
To set or modify the percentage of chemical from 1% to 4%, push the
button until the desidered percentage is showed on the display.
12. Water (fl ow) regulating push-buttons (optional)
Push on + or - to regulate the brush water fl ow. The regulating is shown
by the indicator 10.
!
Caution!
This function is activated by the programs (RCM 02 - RCM 03) only.
13. Water recycling push-button (optional)
14. Spray and suction device kit push-button (optional)
Controls the spray and suction device kit.
15. Diagnostic LED for drive chopper
The LED with a sequence of fl ashes indicates the anomalies on the drive
chopper.
For the fl ashes and anomalies description , see "DIAGNOSTICS - LED pag.62".
25
cleaning.
Tabla de contenido
