Bosch GBM 10 PROFESSIONAL Instrucciones De Servicio página 17

OBJ_BUCH-321-001.book Page 17 Thursday, January 25, 2007 8:36 AM
Technical Data
Rotary drill
Article number
Rated power input
Output power
No-load speed
– 1st gear
– 2nd gear
Rated speed
– 1st gear
– 2nd gear
Rated torque (1st/2nd gear)
Spindle collar dia.
Speed preselection
Speed control
Right/left rotation
Maximum drilling diameter
(1st/2nd gear)
– Steel
– Wood
– Aluminium
Max. screw dia.
Chuck clamping range
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] of 230/240 V. For lower voltage and models for specific countries, these val-
ues can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
Declaration of Conformity
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 60745 according to
the provisions of the
98/37/EC.
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
22.11.2006, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
1 609 929 K97 • 25.1.07
GBM ... 10
PROFESSIONAL
0 601 ... 135 0..
W 450
W 220
rpm 2000
rpm
rpm 1300
rpm
Nm 6.0/–
mm 43
mm 10/–
mm 25/–
mm 13/–
mm
mm 1–10
kg 1.5
/II
directives 89/336/EEC,
10 RE 10 SRE 10-2 RE
135 5.. 137 5.. 168 5..
450 420 500
220 220 270
0–2200 0–2600 0–1150
– – – 0–2100
0–1300 0–1600 0–800
– – – 0–1500
6.0/– 6.0/– 9.5/5.0 11.5/6.0 11.5/6.0
43 43
– – –
–
–
10/– 10/– 10/6
25/– 25/– 25/15
13/– 13/– 13/8
– – 6
1–10 1–10 1–10
1.5 1.5
/II /II
Assembly
Auxiliary Handle (GBM 13-2/
GBM 13-2 RE) (see figure A)
Operate your machine only with the auxiliary
handle 11.
The auxiliary handle 11 can be set to any position for a
secure and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary
handle 10 in anticlockwise direction and set the auxil-
iary handle 11 to the required position. Then tighten the
wing bolt 10 again in clockwise direction.
Adjusting the Drilling Depth
The required drilling depth X can be set with the depth
stop 12.
Loosen the wing bolt for the depth stop adjustment 9
and insert the depth stop rod into the auxiliary handle
11.
The knurled surface of the depth stop 12 must face
upward.
13-2 13-2 RE
169 0.. 169 5..
550 550
285 285
1000 0–1000
1900 0–1900
550 0–550
1000 0–1000
43 43 43
–
–
–
13/8 13/8
32/20 32/20
20/12 20/12
– – –
1–13 1–13
1.7 1.9 1.9
/II /II /II
English | 17