DWT KGS12-210 Manual Original página 25

• Loosen lock-nut 42�
• Adjust the cutting depth by turning bolt 41 in or out�
• Tighten lock-nut 42�
Vertical alignment of the body and adjustment of
the 45° tilt (see fig. 14-17)
• Position the body for carriage�
• Loosen lock lever 1 and set the body tilt
angle (90° or 45°)� Tighten lock lever 1�
• Place the sides of an alignment setsquare 90° or 45°
(depending on the angle to align) to the surface of saw
blade 5 and turntable 16� If the setsquare sides join
the surfaces of saw blade 5 and table 16 tightly, then
alignment is not needed, otherwise you have to do it�
Use bolt 43 and lock-nut 44 for vertical align-
ment of the body (see fig. 14, 16).
Use bolt 45 and lock-nut 46 for adjustment
of the body tilt angle 45° (see fig. 15, 17).
• Loosen lock lever 1�
• Loosen the lock-nut�
• Turning the adjustment bolt in or out, makethe sides
of the 90° or 45° setsquare (depending on the angle
to adjust) join the surfacesof saw blade 5 and table 16
tightly�
• Tighten the lock-nut�
• Loosen screw 48 and place indicator 47 to the 0°
(on scale 2) or 45° position (depending on the angle to
adjust), then tighten screw 48�
Retaining bar alignment (see fig. 18-19)
• Set the 0° horizontal cutting angle (the procedure is
described below)�
• Position the body for carriage�
• Place the sides of an alignment setsquare 90° to the
surface of saw blade 5 and re taining bar 14� If the
setsquare sides join the surfaces of saw blade 5 and
retaining bar 14 tightly, then alignment is not needed,
otherwise you have to do it�
• Loosen retainer bolts 27, and by moving retaining
bar 14 make the sides of the 90° setsquare join the
surfaces of saw blade 5 and retaining bar 14 tightly�
• Tighten retainer bolts 27�
Kerf indicating laser alignment (see fig. 20)
Before starting any work, ensure that the kerf indicat-
ing laser is properly aligned�
• Make a kerf in the blank, but do not cut it (the proce-
dure is described below)�
• Turn on the kerf indicating laser (using on / off
switch 31) - the laser beam should accurately point at
the kerf, otherwise - align the laser�
• Loosen screws 49�
• Move the body of kerf indicating laser 3 to theright
and left until the laser beam points accurately at the kerf�
• Tighten screws 49�
Initial operating
of the power tool
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power
[KGS12-210]
Switching on:
Press blocking lever 10 with thumb of the right hand
(see fig. 21) - this will enable you to pull the power tool
body down� Press on / off switch 25�
Switching off:
Release on / off switch 25�
[KGS16-255]
Switching on:
Press blocking level 10 to the left with your right hand
(see fig. 21) - this will enable you to press on / off
switch 25 easily and pull the power tool body down�
Press on / off switch 25�
Switching off:
Release on / off switch 25�
the power tool operation
Dust suction allows reducing dust concen-
tration in the air and prevents its accumula-
tion at the workplace�
While operating the power tool, always
use dustbag 33 or a vacuum cleaner suitable for
collecting process-generated dust� A special adapter is
used to join the vacuum cleaner to coupler 4�
on the power tool operation
Alignment of the horizontal cutting angle (see
fig. 22-23)
[KGS12-210]
• Loosen lock 19 (see fig. 22).
• Set the cutting angle by turning the powertool body�
Indicator 20 shows the set cuttingangle on scale 21�
• Tighten lock 19�
[KGS16-255]
• Loosen lock 19 and press fixing lever 18 (see
fig. 23).
• While pressing lever 18, set the cutting angle by
turning table 16 by lock 19� Indicator 20 shows the set
cutting angle on scale 21�
• Release fixing lever 18 and tighten lock 19�
You can preset the most frequent angles (45°, 22�5°, 0°,
etc�)�
• Loosen lock 19 and press fixing lever 18�
• While pressing lever 18, set the cutting angle by
turning table 16 by lock 19� As soon as indicator 20
shows one of the frequent angles (45°, 22�5°, 0°, etc�)
on scale 21 - release fixing lever 18, and the chosen
angle will be properly fixed, you do not have to tighten
lock 19 in this case�
English
25
tool on / off
Dust suction during
Recommendations