Idiomas disponibles
Idiomas disponibles
ENGLISH
5. OPERATION
Once the robot's light indicator changes from oscillating orange to steady blue, the battery is
fully charged and the robot is ready to operate.
The robot cannot operate with low battery.
Recommendations: Remove all cables and obstacles from the floor before operating the robot
in order to avoid accidents and damage.
5.1. Robot buttons
Fig.15.
Auto mode
Press the power button on the robot for it to start cleaning automatically, first a cleaning cycle
in Edge mode and then another cycle in and organized zigzag motion, recognizing which areas
it has cleaned and which ones it has not. The robot will automatically plan the cleaning route
as it is cleaning. If during this mode the robot is controlled manually, the robot will calculate
the route again and could go through previously cleaned areas. In order to ensure efficient
cleaning, do not operate it manually during auto mode cleaning.
Thanks to its Total Surface 2.0 technology, if the battery is low during the cleaning cycle, the
robot will smartly return to the charging base automatically and, once it is fully charged, it will
resume the cleaning process from the same point, offering a high-efficiency cleaning.
During cleaning, the robot will stop briefly to evaluate the area and calculate the cleaning
route (this stop will vary depending on the house conditions).
Note: The robot cleans in an organized way and per 4x4 m squared areas, therefore it might
leave the room where it is cleaning to finish off the delimited area. Do not worry, the robot will
clean all the accessible surface.
Back home mode
Press the back home button on the robot in order to send it to the charging base. This mode
can be activated during any other cleaning cycle and the robot will stop cleaning and return to
the charging automatically.
The robot will take the shortest route back to the charging base thanks to its map memorizing
and the smart back home function. When a cleaning cycle has been completed or the robot's
battery is low, thanks to its Total Surface 2.0 technology, the robot will also return to the
charging base to avoid running out of battery.
Warning: Remove the Wet & dry tank during charging.
5.2. Remote control
Fig.16.
1. Schedule
2. Power levels (Turbo/Normal/Eco)
3. Back home
34
4. Clock
5. Manual control
6. On/Pause
7. Edge mode
Remote control binding
If the robot does not respond to the remote control, follow the below steps:
Press the edge mode button on the remote control for 5 seconds for the remote control to
enter pairing mode. The screen will display 8888.
The remote receiver will be activated in 5 seconds and will enter pairing mode. The
remote control's signal is received and the remote control returns to normal status. The
display will show pairing is completed.
If the pairing process is unsuccessful, the remote control will display 8888 and will exit the
pairing mode after 30 seconds.
The following modes and operations can be activated from the remote control.
Modes
The first time the robot is operated, it will map and save the whole house's map by means of its
laser before starting the cleaning cycle. Use the robot in Auto mode and Eco power level, this
way you will ensure the robot memorizes the full map.
Note: Make sure the light indicator is lighted in blue before starting cleaning, indicating it is
activated. If not, press any button on the remote control to wake it up.
Auto mode
Fig.17.
Press the power button on the robot for it to start cleaning automatically, first a cleaning cycle
in Edge mode and then another cycle in and organized zigzag motion, recognizing which areas
it has cleaned and which ones it has not. The robot will automatically plan the cleaning route
as it is cleaning. If during this mode the robot is controlled manually, the robot will calculate
the route again and could go through previously cleaned areas. In order to ensure efficient
cleaning, do not operate it manually during auto mode cleaning.
Thanks to its Total Surface 2.0 technology, if the battery is low during the cleaning cycle, the
robot will smartly return to the charging base automatically and, once it is fully charged, it will
resume the cleaning process from the same point, offering a high-efficiency cleaning. During
cleaning, the robot will stop briefly to evaluate the area and calculate the cleaning route (this
stop will vary depending on the house conditions).
Note: The robot cleans in an organized way and per 4x4 m squared areas, therefore it might
leave the room where it is cleaning to finish off the delimited area. Do not worry, the robot will
clean all the accessible surface.
ENGLISH
35
