Industry Canada Certification @ Am-Modbus-Wb, Am-Stick-Wb - ZIEHL-ABEGG ECblue Serie Instrucciones De Montaje

Instrucciones de montaje ECblue BASIC-MODBUS, ECblue BASIC
Caution
The FCC requires the user to be notified that any changes or modifications made to this device that
are not expressly approved by ZIEHL-ABEGG SE may void the user's authority to operate the
equipment.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help
Labeling Requirements
The Original Equipment Manufacturer (OEM) must ensure that FCC labelling requirements are met.
This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate
Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC
ID: T7V1740. This FCC identifier is valid for all PAN1740 modules.
In any case the end product must be labelled exterior with "Contains FCC ID: T7V1740"
Antenna Warning
For the related part number of PAN1740.
This device is tested with a standard SMA connector and with the antennas listed below. When
integrated in the OEMs product, these fixed antennas require installation preventing end-users from
replacing them with non-approved antennas. Any antenna not in the following table must be tested to
comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for emissions.
Item Part Number
1 LDA212G3110K
RF Exposure
The radiated output power of PAN1740 with mounted ceramic antenna (FCC ID: T7V1740) is far
below the FCC radio frequency exposure limits.
Nevertheless, the PAN1740 shall be used in such a manner that the potential for human contact
during normal operation is minimized
1.7.3 Industry Canada Certification @ AM-MODBUS-WB, AM-STICK-WB
This device contains "Contains IC: 216Q-1740".
PAN1740 is licensed to meet the regulatory requirements of Industry Canada (IC), license: IC: 216Q-
1740.
Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any
regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain
Canadian information on RF exposure and compliance from www.ic.gc.ca.
This device has been designed to operate with the antennas listed in the Table above, having a
maximum gain of 0.9 dBi. Antennas not included in this list or having a gain greater than 0.9 dBi are
strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The antenna
used for this transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Due to the model size the IC identifier is displayed in the installation instruction only and can not be
displayed on the modules label due to the limited size (8.7x15.6mm).
L-BAL-F078D-E 1939 Index 003
Manufacturer Frequency Band
Murata 2.4 GHz
Nro. de art.
8/79
Notas generales
Type Gain (dBi)
Chip-Antenna +0.9