Optional Accessories - Makita DCL140 Manual De Instrucciones

Nozzle + Extension wand (Straight pipe) (Fig. 30)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for
cleaning a floor while standing erect.
Corner nozzle (Fig. 31)
Fit on the corner nozzle for cleaning corners and crevices
of a car or furniture.
Corner nozzle + Extension wand (Straight pipe)
(Fig. 32)
In tight quarters where the cleaner itself cannot squeeze
in, or in high places hard to reach, use this arrangement.
Cleaning without nozzle (Fig. 33)
You can pick up powder and dust without nozzle.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off before
attempting to perform inspection or maintenance.
Cleaning
NOTICE:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
• Do not blow dust sticking on the cleaner and filters
by air duster. It brings dust into the housing and
causes failure.
• After washing filters, dry them thoroughly before
use. Insufficiently dried filters may cause poor suction
and shorten the service life of the motor.
• After cleaning filters and sponge filter, be sure to
re-install them before use. If you use the cleaner
without filters and sponge filter, dust comes into the
motor housing and cause malfunction.
Things to Check Before Asking for Repairs
Symptom
Weak suction power
Not working
010051
NOTE:
• Do not attempt to repair cleaner by yourself.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Extension wand (Straight pipe)
• Nozzle
Area to be investigated
• Is capsule full of dust?
• Is filter clogged?
• Is battery exhausted?
• Is battery exhausted?
Cleaner body
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening and filter mounting
area. (Fig. 34)
Filter
Wash the filter in soapy water when it is clogged with
dust and the cleaner power becomes weak. Dry it out
thoroughly before use. (Fig. 35)
Sponge filter
When the sponge filter becomes dirty, clean it as
follows.
1. Remove the filter.
2. Pull out the sponge filter from between the pillars.
3. Clean the sponge filter by tapping or washing. If you
wash it, dry it out thoroughly before use.
4. Insert the sponge filter from between the pillars and
set it in the original position. Make sure that each
bottom edge of the pillar holds down the sponge fil-
ter, and there is no gap between the sponge filter
and suction opening. (Fig. 36)
Wall mount for cordless cleaner
Optional accessory
NOTE:
• The screw to mount the holder is not included. Prepare
a screw which fits with the material to screw into.
Attach the wall mount for cordless cleaner to a hard
wooden wall, beam or column, where the wall mount for
cordless cleaner can be firmly secured. Always be sure
that the wall mount for cordless cleaner is securely
attached before hanging the cleaner. (Fig. 37)
CAUTION:
• Do not hang the cleaner to the wall mount violently
or hang other appliances than the cleaner.
• Empty dust from capsule.
• Dust down or wash filter.
• Recharge battery.
• Recharge battery.
• Nozzle for carpet
• Shelf brush
• Corner nozzle
• Round brush
• Flexible hose
• Filter
• Prefilter
• High performance filter
• Wall mount for cordless cleaner
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Fixing method
11