Servicing; Maintenance; Tube Element Replacement; Replacement Part List - Bromic Heating TUNGSTEN SMART-HEAT 2000W Manual Del Usuario

SERVICING

! WARNING
Servicing and maintenance MUST be carried out by an
authorised and licensed person only
!
WARNING
ELECTRICAL SHOCK HAZARD!
Serious injury or death may occur.
Disconnect from electrical supply before servicing this
heater.

MAINTENANCE

For longest product life & to maintain product appearance
mount heater under cover & protect from rain & weather
whenever possible.
The exterior housing of the heater should be cleaned
regularly with a soft damp cloth. For locations near the
coast, salt in the air can cause rusting of metal. Additional
cleaning of the heater with a soft damp cloth fortnightly will
increase the life of the products appearance.
Ensure that there is no excessive build-up of dirt/dust on
the reflectors or elements as this can cause overheating
and premature element failure. To clean the reflectors and
elements, ensure heater is off and has been off for at least 2
hours after operation, and wipe off any dirt/dust with a soft
& dry cloth.

TUBE ELEMENT REPLACEMENT

1. Remove Front Cover of the heater by unscrewing the 3
screws holding it in place.
2. Remove first Element End Cover by unscrewing the 2
screws holding it in place.
3. Open first Element Lock Bracket by removing screw.
4. Remove outer Hex Nut, Spring Washer and Lead Wire
Ring Terminal from the threaded stud.
5. Repeat steps 2-4 to release second end of element.
6. Remove old Tube Element.
7. Assemble new Tube Element.
Hex Nut, Spring Washer and Ring Terminal must be
assembled tightly at both ends of element.
8. Element Lock Brackets and Element End Covers must
be replaced at both ends of the heater. Assemble front
cover and secure with 3 screws.
12
All manuals and user guides at all-guides.com
1.
2.
2000W & 3000W Models 4000W & 6000W Models
3.
2000W & 3000W Models 4000W & 6000W Models
4.
www.bromicheating.com

REPLACEMENT PART LIST

No. Description
1 Tube Element
2 Front Cover
3 Element End Cover Set
4 Junction Box Cover & Seal Set
5 Mounting Bracket Set (Short)
6 Mounting Bracket Set (Long)
7 Tube Suspension Kit
8 Chain Suspension Kit

TROUBLESHOOTING

SYMPTOM POSSIBLE CAUSE (S)
Element does not energize 1. Defective element
2. Improper connection
Not enough heat 1. Heater too small for application
2. Heater mounted too high or too
far
Too much heat 1. Heater too large for application
2. Heater mount too low or too close
Hot spot in Tube 1. Heater is not level
2. Grease or moisture on tube
Version 1.0ES
BH0420006 BH0420007 BH0420008
(2000W) (3000W) (4000W)
BH8180001 BH8180002 BH8180001
BH8180003 BH8180004 BH8180003
BH8180005 BH8180006 BH8180005
BH8180007 BH8180007 BH8180007
BH8180008 BH8180008 BH8180008
BH8180009 BH8180009 BH8180009
BH8180012 BH8180012 BH8180012
BH8180013 BH8180013 BH8180013
CORRECTIVE ACTION
1. Replace element
2. Check connection to power
outlet
1. Add additional heater(s)
2. Decrease mounting height or
distance
1. Replace with smaller heater
2. Increase mounting height or
distance
1. Adjust to level mount
2. Clear tube-replace if problem
persists
Revised: 04/09/2013
www.bromicheating.com
BH0420009
(6000W)
BH8180002
BH8180004
BH8180006
BH8180007
BH8180008
BH8180009
BH8180012
BH8180013
13