Using The Lock Menu; Troubleshooting Guide; Connection To Other Equipment - Toshiba 20AS22 Manual De Instrucciones

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

SETTING V-CHIP
This TV is fitted with a V-CHIP controller which provides you with channel viewing access controls and restrictions.
This function is to prevent your children from watching violent or sexual scenes that you may choose to exclude.
Press MENU and press SET + or – until the indicator next to "V-CHIP SET" begins to flash, then
1
press ENTER.
Enter your password (4 digits) using the Direct channel selection buttons (0-9).
2
In the event of entering incorrect password press RESET. Then press ENTER.
Enter the same password for confirmation, then press ENTER.
3
Press SET + or – until the indicator next to "V-CHIP" begins to flash.
4
Press ENTER to select ON.
Press SET + or – until the indicator next to "TV RATING" or "MOVIE RATING" begins to flash. Press ENTER.
5
Press SET + or – to select the desired rating for the applicable video or TV channel. Press ENTER.
6
TV RATING
SET –
SET +
TV-Y
TV-Y7
TV-G
TV-PG
OFF
TV-Y
: all children
TV-PG
TV-Y7
: 7 years old and above
TV-14
TV-G
: children's program
TV-MA
When you select TV-Y7, TV-PG, TV-14 or TV-MA, press RECALL to explain the rating.
Press the SET + or – to select the desired rating you want. Press ENTER to select the setting ON or OFF.
MOVIE RATING
SET –
OFF
G
PG
PG-13
G
: all ages
PG
: parental guidance
PG-13
: parental guidance less than 13 years old
Press MENU repeatedly until the MENU screen is cleared.
7
NOTES:
• If you want to change your password, follow steps 1 and 2 and select "CHANGE PASSWORD" option. Then
enter your new password.
• The V-Chip function is activated only on programs and tapes that have the rating signal.
• Once you block a program using the V-Chip function, the blocked program cannot be watched based on the
content of the show. When the program starts, the "INPUT PASSWORD" will appear on the screen. When you
want to release the V-Chip temporarily, enter the password.
If you change the channel or turn off the TV while the V-Chip function was temporarily released, the original
setting will be resumed. If you return to the channel you were watching you must re-enter your password to
temporarily release your V-Chip function again.
• When you watch the TV using a cable box or a VCR and the TV is tuned to channel 3 or 4, you must release
the V-Chip temporarily. The V-Chip setting will not be resumed until you turn off the TV. The TV channel is not
used in this case.
• When changing the channel with the cable box or the VCR, approximately 10 seconds will pass until the
program appears.
ADJUSTING PICTURE
You can adjust the settings for color, sharpness, contrast, brightness and tint.
Press MENU.
1
Press SET + or – until the indicator next to "PICTURE" begins to flash, then press ENTER.
2
Press ENTER repeatedly to select the item you want to adjust.
3
BRIGHTNESS
CONTRAST
COLOR
Press SET + or – button to adjust the setting.
4
+
BRIGHTNESS
increase brightness
CONTRAST
increase contrast
COLOR
brilliant color
greenish color
TINT
SHARPNESS
makes picture clearer
TO RETURN TO INITIAL SETTING
Press RESET while the picture adjusting mode appears on-screen.

CONNECTION TO OTHER EQUIPMENT

The exact arrangement you use to interconnect various video and audio components to the TV is dependent on
the model and features of each component. Check the Owner's Manual provided with each component for the
location of video and audio inputs and outputs.
The connection diagrams in the following are offered as suggestions. You may need to modify them to
accommodate your particular assortment of components. The diagrams are intended to show component video
and audio interconnections only.
TV/VIDEO SELECTION
If you connect the TV to VCR, camcorder or TV game,
you can select by pressing TV/VIDEO.
Press TV/VIDEO repeatedly to select the desired
mode."VIDEO" will display on the screen for 4 seconds.
VIDEO
1. To connect the TV to a VCR
VCR
Front of TV
VIDEO AUDIO
To Audio/
Video OUT
VIDEO
AUDIO
(not supplied)
3L21001A E
All manuals and user guides at all-guides.com
TV-14
TV-MA
: parental guidance
: 14 years old and above
: 17 years old and above
SET +
R
NC-17
X
R
: under 17 years old parental
guidance suggested
: 17 years old and above
NC-17
X
: adult only
TINT
SHARPNESS
decrease brightness
decrease contrast
pale color
reddish color
makes picture softer
2. To connect the TV to a TV Game
The TV can also be used as a display device for
many video games. However, due to the wide
variety of different types of signal generated by
these devices and subsequent hook-up variations
required, they have not all been included in the
suggested connection diagrams. You'll need to consult
each component's Owner's Manual for additional
information.
To Audio/Video OUT
Front of TV
VIDEO AUDIO
TV GAME
(not supplied)
3. To connect the TV to a camcorder
To playback from the camcorder, connect the
camcorder to the TV as shown.
Front of TV
To AV OUT
jack
VIDEO AUDIO
(not supplied)
5

USING THE LOCK MENU

The LOCK menu includes the CH LOCK, VIDEO LOCK, GAME TIMER and CHANGE PASSWORD
functions.
You can use these functions after entering the correct PASSWORD. (This password is the same one
selected under "SETTING V-CHIP".)
LOCKING CHANNELS
With the CH LOCK feature, you can lock specific channels. You will not be able to tune locked channels
unless you clear the setting. You can choose to lock up to nine TV channels and nine cable channels.
Use the Channel Number Buttons (0-9) to display the television channel you wish to lock.
1
Press MENU, then press SET + or – until the indicator next to "LOCK"
2
begins to flash. Then press ENTER.
3
Use the Channel Number buttons (0-9) to enter your password, then press ENTER.
The LOCK menu appears.
Press SET + or – until the indicator next to "CH LOCK" begins to flash, then press ENTER.
4
Press SET + or – to select:
5
• INPUT to select the channel as one to be locked. Then press ENTER.
• ALL CLEAR to clear all channels from the list of locked channels. Then press ENTER.
Repeat steps 1 through 5 to lock other channels. When you are finished
6
locking channels, press MENU repeatedly until the MENU screen is cleared.
If you try to tune a locked channel, the TV will not display it, but will display the nearest unblocked channel.
NOTES:
• If you are accessing the LOCK menus or V-chip menus for the first time, choose a four-digit number to be
your password.
• After programming CH LOCK, change channels before turning off the television.
• If you want to unlock channels, select ALL CLEAR on step 5, then press ENTER.
LOCKING VIDEO INPUT
With the VIDEO LOCK feature, you can lock out the input source (VIDEO) and channel 3 and 4.
You will not be able to select the input sources with the TV/VIDEO button or Channel buttons unless you
clear the setting.
1
Press MENU, then press SET + or – until the indicator next to "LOCK"
option, then press ENTER.
2
Use the Channel Number buttons (0-9) to enter your password, then press ENTER.
The LOCK menu appears.
3
Press SET + or – until the indicator next to "VIDEO LOCK" begins to flash,
then press ENTER.
4
Press SET + or – to select:
• OFF: Unlocks all video input sources.
• VIDEO: Locks VIDEO.
• VIDEO +: Locks VIDEO, channel 3 and channel 4. This option should be used if you use
the antenna) to play a video tape.
5
Press MENU to return to normal viewing.
SETTING THE GAME TIMER
With the GAME TIMER feature, you can automatically activate the VIDEO LOCK feature (VIDEO setting) to
set a time limit for playing a TV game (30, 60, or 90 minutes).
Press MENU, then press SET + or – until the indicator next to "LOCK", then press ENTER.
1
Use the Channel Number buttons (0-9) to enter your password, then press ENTER.
2
The LOCK menu appears.
3
Press SET + or – until the indicator next to "GAME TIMER" begins to flash, then press ENTER.
Press SET + or – to select a time limit (30 minutes, 60 minutes, 90 minutes or OFF).
4
Press MENU repeatedly until the MENU screen is cleared. After the GAME TIMER is
5
programmed, the display will appear briefly every ten minutes to remind you that the GAME
TIMER is operting. When the programmed end time is reached, the display will change the last
channel automatically.

TROUBLESHOOTING GUIDE

Before requesting service, please refer to the following chart for the symptom and possible solution.
SYMPTOMS
• Make sure the power cord is plugged in.
• Try another AC outlet.
TV does not operate
• Power is off, check fuse or circuit breaker.
• Unplug unit for an hour, then plug it back in.
• Station or CATV experiencing problems, tune to another station.
• Check sound adjustments (VOLUME and MUTE).
Poor sound or No sound
• Check for sources of possible interference.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• Check antenna or CATV connections, adjust antenna.
Poor picture or No picture
• Check for sources of possible interference.
• Check picture control adjustments.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
Poor reception on some channels
• Station is weak, adjust antenna to receive desired station.
• Check for sources of possible interference.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
Poor color or no color
• Check picture control adjustments.
• Check antenna or CATV connection. Adjust antenna.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
Picture wobbles or drifts
• CATV company is scrambling signal.
• Adjust antenna.
• Check all CATV connections.
No CATV reception
• Set TV/CABLE menu option to the CABLE mode.
• Station or CATV system problems, try another station.
Horizontal or diagonal bars on
• Check antenna connections, reorient antenna.
screen
• Check for sources of possible interference.
• Make sure TV/CABLE menu option is in the appropriate mode.
No reception above
channel 13
• If using antenna, check UHF antenna connections.
• Batteries are weak, dead or inserted incorrectly.
• Remote is out of range, move closer to TV (within 15 feet).
No Remote operation
• Make sure Remote is aimed at sensor.
• Confirm there are no obstructions between the Remote and the TV.
• Make sure the power cord is plugged in.
• No broadcast on station tuned.
• Sleep Timer is set.
TV shuts off
• Power interrupted.
• TV station experiencing problems or program tuned is not closed
captioned. Try another channel.
Closed - Caption is not activated
• Check CATV connection or VHF/UHF antenna, reposition or rotate
antenna.
• Press CAP/TEXT to turn on the closed caption decoder.
• Select proper language in the menu options.
Display is not shown in
your language
04/04/2002, 10:53
LOCK
CH LOCK
VIDEO LOCK
GAME TIMER
CHANGE PASSWORD
〈 + / – / ENTER / MENU 〉
CH LOCK
TV
INPUT
--- --- ---
--- --- ---
--- --- ---
ALL CLEAR
〈 + / – / ENTER / MENU 〉
VIDEO LOCK
OFF
VIDEO
VIDEO+
〈 + / – / ENTER / MENU 〉
GAME TIMER
OFF
30
60
90
〈 + / – / ENTER / MENU 〉
POSSIBLE SOLUTIONS
Tabla de contenido
loading

Tabla de contenido