Fitting Instructions - Silver Cross Quantum Manual De Instrucciones

8
Features
A Shock Absorber and Automatic Tensioning System (*)
B Adjustable headrest (6 positions)
C Reclineable backrest (4 positions)
D Seat belt clamps (unidirectional and self-stopping)
E Centralized harness Adjustment
F Shell ventilation
G Side Impact Protection (**)
H Harness adjustment belt
I Harness buckle
J Harness straps
K Shoulders' protections
L Reclining lever
M Headrest adjustment lever
N Support leg articulation
O Support leg
P Support leg adjustment push button
Q Indicators of Iso-fix connector' s engagement
R Push button for Isofix connector' s disengagement
S Levers for the Isofix connectors' extension
T Isofix connectors
U Plastic guides for Isofix connectors
Notes:
(*) "SA-ATS" means "Shock Absorber and Automatic Tensioning
System". This child seat is equipped with an added safety device,
providing a proved shock absorption and the automatic retraction of
the harness, reducing the consequences due to a frontal accident.
(**) this child seat is designed to provide a superior protection in case
of lateral shocks.
WARNING! Only use the car seat in the forward facing
position. The use against the direction of travel is NOT
permitted and could be extremely dangerous in the event
of an accident. Use this child seat ONLY for securing your
child in your vehicle. Please always observe your country
regulations; Should your vehicle be equipped with a front
airbag, please observe any instructions in the vehicle
owner's manual;
All manuals and user guides at all-guides.com
II. Fitting Instructions
The Silver Cross Quantum Car Seat is classified in the SEMI UNIVERSAL
category and can be installed in two different methods:
Method A : For vehicles equipped with Isofix anchor points (cf. list "A"
compatible vehicles).
Method B: For vehicles equipped with three-point safety belt (cf. list
"B" compatible vehicles).
Method A: Installing the car seat using the Iso-fix connectors
Rotate the support leg so that it is in an upright position (Fig. 2).
To prepare the child seat for installation, press simultaneously the two
levers, on either side of the child seat base (Fig. 3 - A) and push the
support leg release unit (Fig. 3 - B), to extract the connectors (Fig. 3 - C).
The Silver Cross Quantum car seat comes with two plastic guides (Fig.
1 - U). You can use them, if your vehicle has none, to guide the Isofix
connectors into their proper position, in correspondence with the seat
anchor points of your car. Line up the two plastic guides with the Isofix
connecting points (Fig. 4 ).
Place the child seat on the appropriate vehicle seat, facing forward.
Ensure the vehicle seat is locked in the most upright and adjusted to
the rearward position.
Make sure that the connection indicators are red (Fig. 5A), suggesting
that the connectors are ready for engagement.
If one or both indicators are green, press the button (Fig. 5-R).
Insert simultaneously the two Isofix connectors through the child seat
guides, pushing the support leg articulation (Fig. 5-B) to lock them in.
Important: You must clearly hear two distinct "clicks" and both
indicators should be green (Fig. 5 - C). Only then are the connectors
properly attached to the anchor points of the seat.
Adjust the height of the support leg by pressing the push button
located at its back (Fig. 6) and slide down the lower section until it
reaches the floor of the vehicle. Release the button and check that the
support leg is locked into position and the bottom of the leg is well in
contact with the vehicle's floor.
The support leg is designed to provide stability to the seat, preventing
it from sinking, in the event of an accident.
Firmly push the child seat to make it adhere to the seat back of the
vehicle (Fig. 7).
Important: When adjusting the support leg, make sure that the base of
the seat always remains in contact with the vehicle seat (Fig.8) and not
elevated.
To release the Isofix connectors:
Slide the support leg upwards pressing the adjustment push button
(Fig. 9 - A).
Move the seat forward by pressing the side levers and pulling it forward
(Fig. 9 - B).
Press the push button on the top of the support leg as shown (Fig. 9 -
C), to release the Isofix connectors.
9
silvercrossbaby.com