Tabla de contenido
DISC IN ASSIGNED ORDER.
7.
PRESS "STOP
" BUTTON (13) TO TERMINATE PROGRAM PLAY.
AFTER PROGRAM COMPLETE, PRESS "MEM/CLK-ADJ" BUTTON (7) TO REVIEW THE TRACKS BEING
PROGRAMMED.
PRESS "STOP
" BUTTON (13) AT CD STOP MODE TO CANCEL ALL PROGRAMMED MEMORY.
FOR MP3 DISC / FILE, PRESS THE "FOLDER / PRE-UP "BUTTON (15) TO SELECT THE 1
FOLDER DIRECTLY AND HENCE TO SPEED UP THE SONG SELECTION.
PLAYBACK OF MP3 SONG VIA USB STORAGE MEDIA OR MEMORY CARD
CONNECTING
THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3FILE WHICH STORED IN THE
MEMORY MEDIA WITH USB CONNECTING PORT OR SD/MMC MEMORY CARD.
1.
SET THE SYSTEM AT STANDBY MODE FIRST OR OTHER FUNCTION EXCEPT SD OR
USB MODE.
2.
PLUG-IN THE USB PEN-DRIVE WITH THE FACE UP & MAKE SURE IT GOING
INTO COMPLETELY OR INSERT THE MEMORY CARD IN THE DIRECTION OF THE
ARROW AS SHOWN IN THE LABEL ON THE UNDERSIDE OF THE MEMORY CARD SLOT
COVER. INSERT STRAIGHT WITHOUT BENDING.
CONNECTING THE USB UPSIDE DOWN OR BACKWARDS COULD DAMAGE THE AUDIO SYSTEM OR
THE STORAGE MEDIA (USB THUMB DRIVE / SD/MMC CARD). CHECK TO BE SURE THE DIRECTION IS
CORRECT BEFORE CONNECTION.
1.
PRESS FUNCTIONS BUTTON (4) TO "CARD" MODE OR "USB" MODE.
2.
THE SYSTEM WILL START READING THE STORAGE MEDIA AUTOMATICALLY AFTER CONNECTING, AND
LCD DISPLAY (2) WILL SHOW THE TOTAL NUMBER OF MP3 FILES BEING DETECTED. AND WILL START
PLAYBACK AUTOMATICALLY.
3.
REPEAT THE SAME PLAYBACK PROCEDURE AS PLAYING CD/MP3 DISC AS ABOVE.
REMARK
-
THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3FORMAT ONLY THOUGH THE USB PORT.
-
IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3
ENCODING FORMAT, SOME MP3 PLAYER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. THIS IS
NOT A MAUFUNCTION OF THE SYSTEM.
-
USB PORT DOES NOT SUPPORT CONNECTION WITH USB EXTENSION CABLE AND IS NOT DESIGNED
FOR COMMUNICATION WITH COMPUTER DIRECTLY
ENCODING OF CD/PHONO INTO MP3 FILE TO USB/SD MEMORY
THE SYSTEM IS ABLE TO ENCODE NORMAL CD/TURNTABLE TO MP3 FORMAT AND RECORDING AT MEMORY
MEDIA WITH USB CONNECTING PORT(OR SM/MMC CARD SLOT).BEFORE STARTING THE ENCODING,
PLEASE INSERT THE MEMORY MEDIA (USB PEN DRIVE OR SD/MMC CARD) TO THE SYSTEM & MAKE SURE
IT HAD ADEQUATE FREE MEMORY SIZE FOR RECRODING:-
A) CD ENCODING
I)
ENCODING 1 TRACK
1.
PERFORM NORMAL PLAYBACK OF THE CD TRACK YOU WANT TO ENCODE & RECORD,
2.
PRESS "
" BUTTON (3), THE SYSTEM WILL SHOW "USB" OR "SD" & "
ENCODING IS START TO PERFORM.
3.
AFTER COMPLETING OF RECRODING, UNIT WILL STOP PLAYBACK AUTOMATICALLY.
II)
ENCODING WHOLE DISC
1.
SET CD AT STOP MODE.
2.
PRESS "
" BUTTON (3), THE SYSTEM WILL SHOW "USB" OR "SD"&"
WILL START TO PLAY THE DISC AND ENCODING IS START TO PERFORM.
3.
AFTER COMPLETING OF RECRODING, UNIT WILL STOP PLAYBACK AUTOMATICALLY.
III) ENCODING BY PROGRAM
1.
PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CO DOOR
2.
SELECT THE DESIRE TRACKS BY FOLLOWING "CD DISC PROGRAMMING" PROCEDURES. THEN PRESS
"CD PLAY/PAUSE" BUTTON (14) TO START PLAYBACK.
3.
FOLLOW THE STEP 2 AND 3 AS ENCODING 1 TRACK.
GB- 5
ST
TRACK OF NEXT
" AND FLASHING.
" AND FLASHING. SYSTEM
Tabla de contenido
