Cooling / Fan Operation; Dehumidifying Operation; Adjusting Air Flow Direction; Timer Operation - Kunft KAC4254 Manual De Instrucciones

between the current ambient room temperature and the set
temperature on the remote control.
2. In the AUTO mode, you cannot change the fan speed, as this is
automatically controlled.
3. If the AUTO mode is not comfortable for you, you can choose
another, more comfortable mode manually.

Cooling / Fan operation

Make sure the unit is plugged in and switched
on.
1. Press the MODE button to select COOL
or FAN mode.
2 2. Press the UP/DOWN buttons to set the de-
4
sired temperature. The temperature can be
SHORT
CUT
set between 17º C ~ 30º C in 1º C incre-
1
MODE TIMER
ON
ments.
3
TIMER
FAN
OFF
3. Press the FAN button to select the fan
speed in four steps - Auto, Low, Med
FOLLOW
SLEEP SWING LED
ME
or High.
4. Press the ON/OFF button to start the air
conditioning.
NOTE:
In the FAN mode, the set temperature is not displayed in the remote
control and you are also unable to control the room temperature. In
this case, only step 1, 3 and 4 may be performed.

Dehumidifying operation

Make sure the unit is plugged in and switched
on. The OPERATION indicator on the indoor
1. Press the MODE button to select DRY
mode.
2
3
SHORT
2. Press the UP/DOWN buttons to set the de-
CUT
sired temperature. The temperature can be
1
MODE TIMER
ON
set between 17º C ~ 30º C in 1º C incre-
TIMER
FAN
OFF
ments.
3. Press the ON/OFF button to start the air
FOLLOW
SLEEP SWING LED
ME
conditioning.
NOTE:
In the Dehumidifying mode, you cannot change the fan speed, as this
is automatically controlled.

Adjusting air flow direction

Use the SWING &
30
portable air conditioner
1. Up/Down direction can be adjusted with the
remote control. The auto swing fan angles change by 6 degrees
with each press. If the swing button is pressed continuously for
more than 2 seconds, the feature is activated and will swing up
and down automatically.
2. Left/Right direction can be adjusted with the button on the remote
control. The auto swing fan angles change by 6 degrees with each
press. If the swing button is pressed continuously for more than
2 seconds, the feature is activated and will swing up and down
automatically.
NOTE: when the swing fan or its air direction affects the cooling or
heating of the air conditioning, it will automatically change the swing/
direction.

Timer operation

Press the TIMER ON button to set the unit's
auto-on timer. Press the TIMER OFF button to
Timer on
set the unit's auto-off timer.
To set the Auto-on timer.
1. Press the TIMER ON button. The remote
SHORT
control's LCD will show TIMER ON, the
CUT
1 last Auto-on set time and the signal "H".
TIMER
MODE
ON
It is now ready to reset the Auto-on timer to
2
TIMER
FAN
OFF
START the operation.
FOLLOW 2. Press the TIMER ON button again to set the
SLEEP SWING LED
ME
desired Auto-on timer. The timer increases
in 30-minute increments between 10 and
24 hours.
3. After setting the TIMER ON ,there will be a 1 second delay before
the remote control transmits the signal to the air conditioning unit.
Then, after approximately another 2 seconds, the signal "H" will
disappear and the set temperature will re-appear on the LCD
display window.
1. Press the TIMER OFF button. The remote control's LCD will show
TIMER OFF, the last Auto-off setting time and the signal "H". Now
it is ready to reset the Auto-off timer to stop the operation.
2. Press the TIMER OFF button again to set the desired Auto-off
timer. The timer increases in 30-minute increments between 10
and 24 hours and in 1-hour increments between 10 and 24 hours.
3. After setting the TIMER OFF, there will be a 1 second delay before
the remote control transmits the signal to the air conditioning unit.
Then, after approximately another 2 seconds, the signal "H " will
disappear and the set temperature will re-appear on the LCD
display window.
31
EN
KAC4254
button on the