Hoshizaki KM-100A Manual De Instrucciones página 4

I. INSTALLATION INSTRUCTIONS
1. UNPACKING
WARNING
Children should not be allowed in reach of the packaging elements
(plastic bags and expanded polystyrene) as they are potential
sources of danger.
CAUTION
Remove shipping carton, tape(s) and packing. If packing material
is left in the icemaker, it will not work properly.
1) After removing the packaging, make sure that the icemaker is in good
condition. If in doubt, please do not use the equipment but apply to
professionally qualified personnel.
2) Remove shipping tape holding the door and separator.
3) Remove the protective plastic film from the exterior. If the icemaker
is exposed to the sun or to heat, remove the film after the icemaker
cools.
4) Remove the package of accessories, and check the contents:
a) Outlet Hose
b) Scoop
c) Hose Adapter
d) Duct
e) Screw
f) Leg
g) Power Supply Cord
5) Attach the duct to the rear panel using the three screws provided.
See Fig. 1.
Separator
(inside)
Door
Magnet Catch
How to remove Louver
Screw
Fig. 1
All manuals and user guides at all-guides.com
1
1
1
1
3
4
1
Air Inlet
(Air Filter)
Air Filter
Louver
Duct
Rear View
3
2. LOCATION
IMPORTANT
1. This icemaker is not intended for outdoor use. Normal operating
ambient temperature should be within 7°C to 43°C. Normal
operating water temperature should be within 7°C to 35°C.
Operation of the icemaker, for extended periods, outside
of these normal temperature ranges may affect production
capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a firm and level foundation for the
equipment.
4. Allow at least 5 cm clearance at the right side for proper air
circulation and at least 15 mm clearance at top for ease of
maintenance and/or service should they be required.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
6. Do not place anything on top, front and right side of the
icemaker. Especially, do not block the air inlet at the right side.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
when air temperature is below zero (see "II. 2. PREPARING
THE ICEMAKER FOR LONG STORAGE").
3. INSTALLATION
* Incorrect installation can cause harm to people, animals or things, for
which the manufacturer cannot be held responsible.
* Place the icemaker in the selected permanent site.
* The appliance must be positioned so that the plug is accessible.
4. ELECTRICAL CONNECTIONS
WARNING
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national and local
electrical code requirements. To prevent possible severe electrical
shock to individuals or extensive damage to equipment, install a
proper earth wire to the icemaker. Remove the plug from the mains
socket before any maintenance, repairs or cleaning is undertaken.
* This appliance requires a separate 220 - 240VAC, 10A supply. The
electrical supply must be protected by a suitable circuit breaker.
* The main control box fuse is rated at 5A, 250V and should only be
replaced by a qualified service engineer.
* Usually an electrical permit and services of a licensed electrician are
required.
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the
following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
The wire which is coloured Green-and-Yellow must be connected to
the terminal in the plug which is marked with the letter E or by the
symbol or coloured Green or Green-and-Yellow. The wire which
is coloured Blue must be connected to the terminal which is marked
ENGLISH