Idiomas disponibles
Idiomas disponibles
5. Center the template by aligning the forward edge and then the
template left and right trim edges with the decklid.
6. After template is aligned, apply tape to the cut-away regions of
the template in the numerical sequence shown on the template. It
is very important that no bubbles or wrinkles exist in the template
when the tape is applied.
7. Working from the center outward, secure the seven tabs that
indicate the hole locations to the decklid with tape in the area
indicated.
8. Using a center punch and hammer create a small dimple into
the decklid at each of the seven hole locations indicated on the
template.
9. Drill a pilot hole using a 1/8" drill bit at each of the center punch
locations.
10. Remove the template and, using a 3/8" drill bit, enlarge each of
the seven holes.
11. Remove any sharp edges from the holes with a de-burring tool
and apply a zinc rich anticorrosion compound to all bare surfaces
(P/N 12371287 or paint with touchup paint).
12. Clean the decklid surface with alcohol to ensure proper adhesion
of tape.
Note: 7KLV LV YHU\ LPSRUWDQW WR SUHYHQW VSRLOHU HQGV OLIWLQJ.
1RWH 'R QRW UHPRYH WKH WDSH OLQHU IURP WKH VSRLOHU
13. 7HVW ¿W WKH VSRLOHU WR HQVXUH WKH KROHV ZLOO EH LQ WKH ULJKW SRVLWLRQ
by placing the spoiler on the decklid and making sure the bolts
and clips match the hole locations on the template. It may be
necessary to move the clips within their slots to align them with
the decklid holes. If necessary, enlarge any misaligned holes
ZLWK D URXQG ¿OH
14. Using masking tape, tape the tape liner removal tabs on the
leading edge tape to the exterior surface of the decklid to ensure
they are accessible when the spoiler placed onto the decklid.
15. Place the spoiler onto the decklid and align all bolts and clips
with their respective holes.
16. Open the decklid and using a 1/4" drive universal joint with 10mm
socket loosely apply the nuts to the spoiler studs.
17. Close the decklid and adjust the spoiler so that it is centered left-
to-right and aligns well to the contour of the vehicle.
18. Remove the tape line on the outboard pieces of tape (2).
19. Begin removing the tape liner on the leading edge of the spoiler
working from the center of the spoiler towards the driver side.
Press downward on the tape area to ensure good adhesion of
the tape to the decklid.
1RWH 0DNH VXUH WR DSSO\ IRUZDUG SUHVVXUH WR WKH EDFN HGJH
RI WKH VSRLOHU WR PLQLPL]H JDSSLQJ DORQJ WKH UHDU HGJH RI
the spoiler.
1RWH 7KH WDSH VHWV IRUHDIW SRVLWLRQ RI WKH VSRLOHU
Rear Compartment Lid Spoiler Package
ALL INFORMATION WITHIN
DATE
ABOVE BORDER TO BE PRINTED
EXACTLY AS SHOWN ON 8.5 x 11
22SE12
WHITE 16 POUND NON-BOND
RECYCLABLE PAPER.
PRINT ON BOTH SIDES, EXCLUD-
ING TEMPLATES.
TO BE UNITIZED IN ACCORDANCE
WITH GM SPECIFICATIONS.
REVISION
Initial Release - Feng Zhaobin
$SSO\ IRUZDUG SUHVVXUH WR EDFN HGJH RI VSRLOHU WR PLQLPL]H
JDSSLQJ RQ UHDU HGJH RI VSRLOHU
20. :KHQ WKH WDSH OLQHU UHPRYDO HQFRXQWHUV WKH DUHD RI WKH ¿UVW FOLS
press downward on the area of the spoiler above the clip to install
it to the decklid and continue removing the tape liner.
21. Repeat the step above for the second clip.
22. Press downward on the end of the spoiler with an approximate
load of 15kg to create a good tape bond to the decklid / wetout
is achieved.
NRWH 7KLV LV LPSRUWDQW WR SUHYHQW WKH VSRLOHU HQGV OLIWLQJ
23. Repeat steps 19 to 22 working from the center of the spoiler to
the passenger side.
24. Open the decklid and tighten the three nuts beginning with the
center. Torque nuts to 7 N·m.
25. Using a rubber roller, apply 15kg along the leading edge of the
spoiler and the ends of the spoiler to ensure proper tape adhesion.
26. Reinstall the decklid liner.
Decklid
VIEW A
VIEW A
IR 22SE12
INSTALLATION INSTRUCTIONS
AUTH
DR
TITLE
1807861
Rear Compartment Lid Spoiler Package
PART NO.
90801519
Wet out tape
IURP FHQWHU
moving outward.
Template
Spoiler
Clip
Bolt
90801519
PART NO.
SHEET
2
6
SHEET
OF
2
6
OF
