swissflex UNI 20-85RF Manual De Instrucciones página 26

Initial setup «Classic»
Place the batteries into the radio remote control
Remove the cover from the battery compartment (12)
on the back of the radio remote control. Place 3 AAA-
batteries (13) into the compartment, paying attention
to the +/- markings. Close the compartment cover
again. The maximum range of the radio remote control
is 15 metres.
Teaching-in the radio remote control (already
taught-in in the factory)
1. Remove the radio remote control's battery cover on
the back of the device.
2. Insert / check the batteries (3 x AAA).
3. Activate the teach-in button (21) on the switching
power supply (press 2 x). Now the motor's emer-
gency light turns on.
4. Press buttons (1+2) simultaneously on the radio
remote control until the motor's emergency light
turns off. This means that pairing has been com-
pleted.
Synchro function (with sync cable)
When two uni 20_85RF/uni 22_85RF bridge
together with a sync cable (connection jack (14)), the
synchro function is required. By pressing and holding
down the button (2), the synchro function is activated/
deactivated. When pressing the travel button (3-8),
the control systems synchronise and then move in the
confirmed direction of travel. After plugging in the sync
cable, carry out a reset as follows:
Press button (21) on the switching power supply (19)
until all of the motors have powered down and this is
confirmed by the motor's emergency light blinking twi-
ce. (Can take 20 seconds)
The internal meter readings for the individual motors
have now been reset to '0' and the sync function can
work correctly.
Under-floor lighting
Activate the under-floor lighting by pushing the „Un-
der-floor lighting" button (1). This switches off auto-
matically after 30 minutes, or if the button is pushed
once again.
Pocket lamp
The pocket lamp is illuminated when the „Pocket
lamp" button (11) is held down. The light turns off
when the button is released.
26
Operating instructions
Adjustment options «Classic»
RFK:
Buttons (3-8) can be used to individually adjust the head
and back sections as well as the leg section.
RFF:
Buttons (3-8) can be used to individually adjust the
back section as well as the thigh and foot sections.
To reset to the horizontal position
Press the "all motors down" button (10) to simultane-
ously move all sections to the horizontal position.
Care and Maintenance «Classic»
Your uni 20_85RF/uni 22_85RF bridge
ty product that has been designed to serve you reliably
for many years to come. For occasional cleaning and
the removal of dust, we recommend the use of a dry
cloth.
Changing the batteries in the radio remote control
Remove the cover from the battery compartment (12)
® are linked
on the back of the radio remote control. Place three
AAA batteries into the compartment, paying attention
to the +/- markings. Close the compartment cover
again.
Changing the batteries in the uni 20_85RF/uni
22_85RF bridge
teries for emergency lowering)
Carefully remove the batteries from the battery clips.
Place two 9 V block batteries in the compartment, pay-
ing attention to the +/- markings. The batteries in the
switching power supply provide power in the case of a
power failure.
Troubleshooting «Classic»
In case of malfunctions with your uni 20_85RF/uni
22_85RF bridge
ting tips. If the problem cannot be resolved, disconnect
the uni 20_85RF/uni 22_85RF bridge
outlet and contact your Swissflex stockist.
Loss of power in the sitting position; emergency lo-
wering button
The switching power supply (19) contains two bloc
batteries to revert the bed to the horizontal (sleeping)
position in the event of a power failure while sitting up
in the bed:
Hold the emergency lowering button (21) down until all
sleeping surfaces are in the horizontal position. Once
®
® switching power supply (19) (bat-
® , consult the following troubleshoo-
®
is a high-quali-
from the mains
EN