Bevel Cut; Compound Cut - Stanley FATMAX FME720 Manual De Instrucciones

● When the saw reaches full speed, push the main
operating handle (2) down slowly, cutting through the
workpiece.
● Slowly move the main operating handle (2) toward the
fence to complete the cut.
● Release the on/off switch (3) and allow the blade to stop
before allowing the cutting head to rise.
Operating the high sliding fence for all bevel and
compound mitre cuts
● The moveable part of the left side of the fence can be
adjusted to provide maximum support of the work piece
near the blade, while allowing the saw to bevel to a full
47° left. The sliding distance is limited by stops in both
directions.
Adjusting the fence (fig. E)
● Loosen the high sliding fence clamp (20) and slide the
fence to the left.
● Make a dry run with the saw switched off and check for
clearance.
● Adjust the fence to be as close to the blade as practical to
provide maximum work piece support, without interfering
with the up and down movement of the arm.
● Tighten the high sliding fence clamp (20) to secure the
@
fence in place.
Warning! The guide groove can become clogged
with sawdust. Use a stick or low pressure air to
clear the guide groove.

Bevel cut

● Make sure that the high sliding fence is adjusted to the
correct orientation before adjusting the bevel angle.
Note: The saw is fitted with a special 33.9° bevel pin (23) for
special crown moulding.
● Loosen the bevel lock handle (30) (fig. F) and move the
cutting head to the required angle. Tighten the bevel lock
handle (30).
● Operate the on/off switch, then press the release
lever (36) when the saw reaches full speed, push the
main operating handle (2) down slowly, cutting through the
workpiece.
● When the saw reaches full speed, push the main
operating handle (2) down slowly, cutting through the
leading edge of the workpiece.
● Slowly move the main operating handle (2) toward the
fence to complete the cut.
● Release the on/off switch (3) and allow the blade to stop
before allowing the cutting head to rise.
● Make sure that the arm is securely locked when bevelling.

Compound cut

● Make sure that the high sliding fence is adjusted to the
correct orientation before adjusting the bevel angle to
make a compound cut.
A compound cut is a combination of mitre cut and bevel cut.
● Switch the laser on/off switch (1) to on.
● Refer to the above procedures to perform this cut.
(original instructions)
● When the saw reaches full speed, push the main
operating handle (2) down slowly, cutting through the
leading edge of the workpiece.
● Slowly move the main operating handle (2) toward the
fence to complete the cut.
● Release the on/off switch (3) and allow the blade to stop
before allowing the cutting head to rise.
Base moulding cut
Base moulding can be cut vertical against the fence or flat on
the table.
● Refer to the following table:
Vertical position
Settings (back of moulding is
against the fence)
Bevel angle 0 º
Moulding position Left side
Inside
Left at
Mitre angle
45 º
corner
Bottom
Moulding
against
position
table
Keep left
Finished
side of
side
cut
Outside
Left at
Mitre angle
corner
45 º
Bottom
Moulding
against
position
table
Keep left
Finished
side of
side
cut
Crown moulding cut (fig. L)
Crown moulding can only be cut flat on the table with this
mitre saw.
● This mitre saw has special mitre stops on 31.6° left and
right and a bevel stop of 33.9° for special crown moulding,
i.e. 52° between the back of the moulding and the top
flat surface that fits against the ceiling; 38° between the
back of the moulding and the bottom flat surface that fits
against the wall.
● Refer to the following table to make this crown moulding
cut:
Settings Left side
Mitre
Right 31.6 º
angle
Bevel
33.9 º
angle
Inside
corner
Moulding
Top against fence
position
Finished
Keep left side of cut
side
English
Horizontal position
(back of moulding is
flat on the table)
45 º
Right Right
Left side
side side
Right at
0 º 0 º
45 º
Bottom Top Bottom
against against against
table fince fence
Keep Keep left Keep left
right side side of side of
of cut cut cut
Right at
0 º 0 º
45 º
Bottom Top Bottom
against against against
table fince fence
Keep Keep Keep
right side right side right side
of cut of cut of cut
Right side
Left 31.6 º
33.9 º
Bottom against fence
Keep left side of cut
11