Preparing To Paint; Painting - Titan 740 High Rider Manual Del Propietário

Preparing to Paint

Before painting, it is important to make sure that the fluid in the
system is compatible with the paint that is going to be used.
NOTE: Incompatible fluids and paint may cause the
valves to become stuck closed, which would
require disassembly and cleaning of the
sprayer's fluid section.
IMPORTaNT: always keep the trigger lock on the spray gun
in the locked position while preparing the system.
1. Place the siphon tube into a container of the appropriate
solvent. Examples of the appropriate solvent are water for
latex paint or mineral spirits for oil-based paints.
2. Place the return hose into a metal
waste container.
3. Set the pressure to minimum by
turning the pressure control knob to
the "MIN" setting.
4. Move the PRIME/SPRAY valve down
to the PRIME position.
NOTE: hold the return hose in the waste
container when moving the
PRIME/SPRay valve to PRIME in
case the sprayer is pressurized.
5. Turn on the sprayer by moving the ON/OFF
switch to the ON position.
6. Allow the sprayer to run for 15–30 seconds to flush the
old solvent out through the return hose and into the metal
waste container.
7. Turn off the sprayer by moving the ON/OFF switch to the
OFF position.
NOTE: Make sure that the spray gun does not have a tip
or tip guard installed.
8. Move the PRIME/SPRAY valve up to the
SPRAY position.
9. Turn on the sprayer.
10. Unlock the gun by turning the gun trigger
lock to the unlocked position.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
11. Trigger the gun into the metal waste container until the old
solvent is gone and fresh solvent is coming out of the gun.
12. Lock the gun by turning the gun trigger
lock to the locked position.
13. Set down the gun and increase the
pressure by turning the pressure
control knob slowly clockwise.
14. Check the entire system for leaks. If
leaks occur, follow the "Pressure Relief
Procedure" in this manual before
tightening any fittings or hoses.
15. Follow the "Pressure Relief Procedure" in this manual
before changing from solvent to paint.
Be sure to follow the pressure relief procedure
when shutting down the sprayer for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray tips, or
preparing for cleanup.
© Titan Tool Inc. All rights reserved.

Painting

1. Place the siphon tube into a container
2. Place the return hose into a metal
3. Set the pressure to minimum by
4. Move the PRIME/SPRAY valve down to
5. Turn on the sprayer by moving the ON/OFF
6. Allow the sprayer to run until paint is
7. Turn off the sprayer by moving the ON/OFF switch to the
8. Remove the return hose from the waste container and
RAPID
CLEAN
9. Move the PRIME/SPRAY valve up to the
10. Turn on the sprayer.
11. Unlock the gun by turning the gun trigger
12. Trigger the gun into the metal waste container until all air
13. Lock the gun by turning the gun trigger
14. Turn off the sprayer.
15. Attach tip guard and tip to the gun
16. Turn on the sprayer.
17. Increase the pressure by turning the pressure control
NOTE: Turning the pressure up higher than needed to
Trigger lock in
locked position.
5
of paint.
waste container.
turning the pressure control knob to
the "MIN" setting.
the PRIME position.
switch to the ON position.
coming through the return hose into the
metal waste container.
OFF position.
place it in its operating position above the container of
paint.
SPRAY position.
lock to the unlocked position.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
and solvent is flushed from the spray hose and paint is
flowing freely from the gun.
lock to the locked position.
as instructed by the tip guard or tip
manuals.
POSSIBLE INjEcTION haZaRD.
Do not spray without the tip guard in place. Never
trigger the gun unless the tip is in either the spray or
the unclog position. always engage the gun trigger
lock before removing, replacing or cleaning tip.
knob slowly clockwise and test the spray pattern on a
piece of cardboard. Adjust the pressure control knob until
the spray from the gun is completely atomized. Try to
keep the pressure control knob at the lowest setting that
maintains good atomization.
atomize the paint will cause premature tip wear
and additional overspray.
English
RAPID
CLEAN
Trigger lock in
locked position.