Replacing The Filters; Pump Filter; Replacing The Motor Assembly - Titan 740 High Rider Manual Del Propietário

Replacing the Filters

Pump Filter

1. Loosen and remove the filter
body by hand.
2. Slip the filter off of the core
spring.
3. Inspect the filter. Based on
inspection, clean or replace
the filter.
4. Inspect the o-ring. Based on
inspection, clean or replace
the o-ring.
5. Slide the new or cleaned filter
over the core spring with the
filter spring adapter in place.
Push the filter into the center
of the filter housing.
6. Slide the filter body over the
filter and thread it into the filter
housing until secure.
NOTE: The filter housing
should be hand-
tightened, but make
sure the filter housing
is seated fully into the
pump block.
Gun Filter
1. Move the gun trigger lock to the unlocked position.
2. Loosen and remove the handle from the gun body.
3. Turning clockwise, unscrew the filter from the gun body.
NOTE: Left-handed threads require turning the filter
clockwise to remove.
4. Turning counterclockwise, screw the new or cleaned filter
into the gun body.
5. Make sure the handle seal is in position and thread the
handle into the gun body until secure.
6. Move the gun trigger lock to the locked position.
NOTE: For more detail, part number information, and
complete assembly drawings, please see the LX-
80II Professional airless Gun Owner's Manual
(P/N 313-2293).
English
Filter Body
Filter Spring
Filter
Filter Spring
Adapter
Core Spring
O-ring
Filter Housing
Gun
Body
Filter
Handle
Seal
Handle

Replacing the Motor assembly

1. Unplug the unit.
2. Loosen and remove the two (2) motor shroud screws.
Remove the motor shroud.
3. Loosen and remove the three (3) belly pan screws.
Remove the belly pan.
4. Loosen and remove the two (2) motor cover screws.
Remove the motor cover.
5. Disconnect all wires between the motor and the sprayer.
6. Loosen and remove the four (4) control panel screws.
Remove the control panel.
7. Disconnect the wires between the motor and the control
panel.
8. Loosen and remove the two (2) motor controller screws.
Remove the motor controller.
9. Loosen and remove the four (4) motor baffle screws.
Remove the motor baffle.
10. Loosen and remove the six (6) motor mounting screws.
11. Pull the motor out of the gearbox housing.
12. With the motor removed, inspect the gears in the gearbox
housing for damage or excessive wear. Replace the
gears, if necessary.
13. Install the new motor into the gearbox housing.
14. Secure the motor with the six (6) motor mounting screws.
15. Reconnect the wires between the sprayer and the new
motor. (refer to the electrical schematic in the Parts List
section of this manual).
16. Place the baffle over the end of the motor assembly.
Secure with the four (4) motor baffle screws.
17. Place motor controller back into place behind the motor
baffle. Secure with the two (2) motor controller screws.
18. Reconnect all wires between the motor and sprayer.
19. Reconnect the wires between the motor and the control
panel.
20. Replace control panel and secure with four (4) control
panel screws.
21. Place the motor cover back over the motor controller.
Secure with the two (2) motor cover screws.
22. Put the belly pan back in place and secure with the three
(3) belly pan screws.
23. Slide the motor shroud over the motor assembly.
24. Secure the motor shroud with the two (2) motor shroud
screws.
Control Gearbox
Panel housing
Screw
Control
Panel
Belly Pan
Screw
Motor
Belly Pan
Shroud
Screw
Motor Controller Screw
10
Motor Shroud
Motor Mounting
Screw
Motor
Motor
Baffle
Motor Baffle
Screw
Motor Controller
Motor Cover
Motor Cover Screw
© Titan Tool Inc. All rights reserved.