SCHOLTES B 40 L EC Serie Manual De Instrucciones página 26

THE FIRST TIME THE HOB IS CONNECTED TO THE THE FIRST TIME THE HOB IS CONNECTED TO THE THE FIRST TIME THE HOB IS CONNECTED TO THE THE FIRST TIME THE HOB IS CONNECTED TO THE THE FIRST TIME THE HOB IS CONNECTED TO THE
GB
ELECTRICITY MAINS, THE KEYPAD WILL BE ELECTRICITY MAINS, THE KEYPAD WILL BE ELECTRICITY MAINS, THE KEYPAD WILL BE ELECTRICITY MAINS, THE KEYPAD WILL BE ELECTRICITY MAINS, THE KEYPAD WILL BE
LOCKED, AS IS THE CASE EVERY TIME LOCKED, AS IS THE CASE EVERY TIME LOCKED, AS IS THE CASE EVERY TIME
LOCKED, AS IS THE CASE EVERY TIME LOCKED, AS IS THE CASE EVERY TIME
ELECTRICITY IS RESTORED AFTER A BLACKOUT ELECTRICITY IS RESTORED AFTER A BLACKOUT
ELECTRICITY IS RESTORED AFTER A BLACKOUT ELECTRICITY IS RESTORED AFTER A BLACKOUT ELECTRICITY IS RESTORED AFTER A BLACKOUT
OR DISCONNECTION; THE T2 BUTTON SHOULD OR DISCONNECTION; THE T2 BUTTON SHOULD OR DISCONNECTION; THE T2 BUTTON SHOULD OR DISCONNECTION; THE T2 BUTTON SHOULD OR DISCONNECTION; THE T2 BUTTON SHOULD
THEREFORE BE PRESSED IN ORDER TO UNLOCK THEREFORE BE PRESSED IN ORDER TO UNLOCK THEREFORE BE PRESSED IN ORDER TO UNLOCK THEREFORE BE PRESSED IN ORDER TO UNLOCK THEREFORE BE PRESSED IN ORDER TO UNLOCK
THE KEYPAD. THE KEYPAD. THE KEYPAD. THE KEYPAD. THE KEYPAD.
AT THIS POINT THE APPLIANCE IS READY FOR
OPERATION.
BURNER SELECTION AND OPERATION BURNER SELECTION AND OPERATION BURNER SELECTION AND OPERATION BURNER SELECTION AND OPERATION BURNER SELECTION AND OPERATION
The burners differ in size and power. Select the most
suitable burner in accordance with the diameter of the
cookware you wish to use.
The oo symbols in the control area (M) indicate the
position of the relevant burner on the hob.
The burners have thermocouple safety devices which
offer protection against gas leaks. If the burner
flame is extinguished during operation, the ignition device is activated in an attempt to re-ignite the
flame. If this fails, after less than 6 seconds, the
flow of gas to the burner is blocked and the
corresponding display shows the text "F2".
Do not attempt ignition again for at least 1 Do not attempt ignition again for at least 1 Do not attempt ignition again for at least 1 Do not attempt ignition again for at least 1 Do not attempt ignition again for at least 1
minute, so that the escaped gas in the vicinity minute, so that the escaped gas in the vicinity minute, so that the escaped gas in the vicinity
minute, so that the escaped gas in the vicinity minute, so that the escaped gas in the vicinity
of the burner is able to disperse properly. of the burner is able to disperse properly.
of the burner is able to disperse properly. of the burner is able to disperse properly. of the burner is able to disperse properly.
In some cases the non-ignition of a burner may be
due to air which has become trapped in the gas
piping. To make it easier for this air to escape, we
recommend that one of the other burners is
activated.
26
SWITCHING ON THE HOB SWITCHING ON THE HOB SWITCHING ON THE HOB
SWITCHING ON THE HOB
SWITCHING ON THE HOB
Press button T1 (general on/off device):
NOTE: the "on" status of the hob is indicated by the
fact that all the burner displays show "0" (or a
flashing "H" if the corresponding burner is hot due to
previous use).
Press one of the buttons (+ or -) which corresponds to
the burner you wish to ignite.
If the + button is pressed, the burner is ignited in its
safety mode and after approximately 3 seconds
automatically begins operating at its minimum
power level; at this point, if you continue pressing
the + button, it is possible to increase the power
level until it reaches level 9 (max).
If the – button is pressed, the burner is ignited in its
safety mode and after approximately 3 seconds
begins operating at its maximum power level
(power level 9) and remains there; at this point, if
you continue pressing the – button, it is possible
to decrease the power level until it reaches level
1 or the burner is switched off (level 0).
SWITCHING OFF A BURNER SWITCHING OFF A BURNER SWITCHING OFF A BURNER SWITCHING OFF A BURNER SWITCHING OFF A BURNER
Press the + and – buttons corresponding to the burner
you wish to switch off simultaneously.
Alternatively:
Press the – button until level 0 is reached.
Alternatively:
Press button T1 (all burners switch off, even if the lock
function has been activated; window D1 is
activated).
SETTING A COOKING TIME SETTING A COOKING TIME SETTING A COOKING TIME SETTING A COOKING TIME SETTING A COOKING TIME
An operating duration may be set for one burner (the
procedure can be performed on all burners but only
one at a time; it is not possible to have several
burners operating with a set duration).
The burner may be operating already or still switched
off (it can only be switched on after the cooking
duration has been set).
To select and set this option:
Press button T3; windows D3, 4, 5 and 6 flash
alternately, displaying the symbol "t" and window D2
displays the figure "99" (the maximum time value
which may be set).
Select the desired burner using + or -;
Use timer buttons T3 and T4 to set the desired cooking
time.
The power level indication appears on the "timed"
burner as usual (although this may be modified
during the operating period), interrupted every 10
seconds by the indication t t t t t ;
At the end of the operating period, the burner switches
off and a buzzer sounds;