Technical Data; Brief Description; Mains Connection - Felisatti HF25/1500 Instrucciones De Servicio

Model
Rated power
Impact rate
Impact energy
Tool holder/bit length
Acoustic pressure
Sound-power level
Vibration acceleration
Weight according EPTA-Procedure 01/2003
Follow very carefully the instructions in this manual, save it
and keep close at hand, ready to carry out any inspection of
parts that may be necessary.
If the machine is used carefully and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the tool
is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
1. Tool holder (hexagon socket)
. Front cover
. Tool retainer
. ON/OFF switch
5. Lock-on button
6. Supply cord with plug
7. Oil gauge
8. Auxiliary handle
9. Ventilation slots

BRIEF DESCRIPTION

This power tool is designed for chiselling, chipping and
demolishing concrete, rocks and asphalt with high efficiency.
A pneumatic percussion unit generates the power necessary
for hammer drilling or chiselling in masonry.
Just like when we hit a conventional chisel with hammer,
a free piston strikes the bit or chisel, which can move
lengthways, through an intermediate part.
This free piston is driven by a second piston activated by an
electric motor through an air cushion. This electro-pneumatic
principle offers great percussion elasticity and work free from
recoil.
BEFORE USING THIS TOOL
WARNING! Before carrying out any work, check, for instance,
using a metal detector, that there are no elec-tric wires or gas
or water pipes under the surfaces you wish to work on.
Make sure the mains voltage is correct: it must be the same
as that on the specification label. Machines with 230V can
also be connected to a 220-V mains supply.
WARNING! Always disconnect the plug from the socket
before doing any work on the machine.
Always check the position of ON/OFF switch. The power tool
must be connected to the power supply socket only when
this switch is in OFF position. If the plug is con-nected to


TECHNICAL DATA

HF25/1500
W 1500
/min 1400
J
mm
dB(A)
dB(A)
m/s²
Kg.
a receptacle while the power switch is in the ON position,
the power tool will start operating im¬mediately, which could
cause a serious acci¬dent.
• Make sure the cord and the plug are in order. If the
replacement of the supply cord is neces¬sary, this has to be
done by the manufacturer or his agent in order to avoid a
safety hazard.
• Switch off and unplug the machine prior to any proce-
dure on the power tool or in case of mains drop out.
• In case of work area remote from the power source,
use as short as practicable extension cord with proper cross-
section.
• Make sure the auxiliary handle is properly mounted and
securely fastened.
hanging the position of the auxiliary handle
1. Unscrew the auxiliary handle M in an anticlockwise
direction.
. Turn the auxiliary handle M to the required position.
. Screw the auxiliary handle M in place again.
1. Clean and then smear the tool shank with grease or
machine oil (Fig. 1).
. Pull the tool retainer lever () toward yourself.
3. Rotate 180° clockwise the tool retainer lever (3) while
pulling it.
. Next, insert the tool shank into the hexagonal tool holder
(1) on the front cover ().
5. Clamp the tool by turning the tool retainer () by half a turn
in the opposite direction (Fig. ).To remove the bit, follow the
above described procedures in reverse order.
Warning! Connect only to a single-phase AC current supply
and only to the mains voltage specified on the rating plate.
Connection to sockets without earth protec-tion is possible as
the appliance features protective class II insulation according
to European Standard EN50114. Radio interference
suppression complies with the European Standard EN
55014.
SWITCHING ON - SWITCHING OFF
Brief activation:
5
30/410
80,6
105
27.0
16,0
CHANGING THE POSITION OF
THE AUXILIARY HANDLE
FITTING THE WORKING TOOLS

MAINS CONNECTION

HF30/2000V
2000
1500
11
84,0
106
15,
19,8