Hoover SteamJet STEAM&SWEEP SSW 1700 Manual De Instrucciones página 4

Sweeping floors
The sweep mode allows you to clear the floor of any small debris before steam cleaning.
ImpoRtANt: Ensure the carpet glider, textile pad a nd pad plate are removed from the
floor head.
1. Plug the steam cleaner into the main power and switch on the cleaner. The red on light
will illuminate.
2. Turn the mode selector dial to sweep mode the blue sweep light will illuminate. [9]
3. Recline the cleaner by placing a foot on the floor head and lowering the main body
towards the floor. [10]
4. To start sweeping press the steam / sweep trigger. [11]
5. Move the cleaner slowly backwards and forwards paying particular attention to hight
raffic areas. [12]
Steam cleaning hard floors
NotE: Always sweep the floor prior to use to remove any loose dirt or debris.
ImpoRtANt: do not use the cleaner without a textile pad and plate attached to the floor
head.
NotE: do not use the carpet glider when cleaning hard floors.
1. Plug the steam cleaner into the main power and switch on the cleaner. The red on light
will illuminate.
2. Turn the mode selector dial to steam mode. [13]
3. After a few seconds the green Steam Ready light will illuminate indicating the cleaner is
ready for use.
4. Recline the cleaner by placing a foot on the floor head and lowering the main body
towards the floor. [10]
To produce steam press the steam / sweep trigger button. [11]
5.
6. Move the cleaner slowly backwards and forwards paying particular attention to high
traffic areas. [12]
Refreshing carpets
NotE: Always sweep the floor prior to use to remove any loose dirt or debris.
ImpoRtANt: do not use the cleaner without a textile pad and plate attached to the floor
head.
Attach the carpet glider to the floor head. [14]
1.
2. Plug the steam cleaner into the main power and switch on the cleaner. The red on light
will illuminate.
Turn the mode selector dial to steam mode. [13]
3.
4. After a few seconds the green Steam Ready light will illuminate indicating the cleaner is
ready for use.
5. Recline the cleaner by placing a foot on the floor head and lowering the main body
towards the floor. [10]
To produce steam press the steam / sweep trigger button. [11]
6.
7. Move the cleaner slowly backwards and forwards paying particular attention to high
traffic areas. [12]
SteamJet-SteamSweepManual__1-3_union.indd 2
CLEANER MAINTENANCE
ImpoRtANt: ALWAyS ENSURE thE cLEANER hAS FULLy cooLEd doWN BEFoRE
pERFoRmING ANy mAINtENANcE tASKS.
Empty the dust container
Note: Empty the dust container after each use.
1. Lift the dust container out of the floor head. [15]
2. Empty the dust container and return to the floor head.
Empty the water tank
3. Unplug the cleaner from the main power and ensure the unit has cooled.
4. Remove the clean water tank for the main body of the cleaner. [4]
5. Twist the cap anti-clockwise and remove. [5]
6. Empty any excess water from the tank. [16] Replace the cap and return to the cleaner.
Removing and cleaning the textile pad
1. Unplug the cleaner from the main power and ensure the unit has cooled.
2. If necessary remove the carpet glider.
3. Press the release pedal at the rear and remove the pad plate from the floor head. [17]
4. Peel the textile pad from the pad plate. [18]
5. Wash the textile pad in a washing machine with a mild detergent at max temperature
40°C.
IMPORTANT: Do not use bleach or fabric softener when washing the textile pad.
Replacing the hard water filter
The cleaner is fitted with a hard water filter. If you live in an area of hard water the filter will
discolour over time. Depending on the water hardness and frequency of use the filter should
be changed every 6 months.
1. Unplug the cleaner from the main power and ensure the unit has cooled.
2. Remove the clean water tank for the main body of the cleaner. [5]
3. Lift the hard water filter out of the cleaner. [19] Replace with new filter.
4. Reassemble the clean water tank to your cleaner.
Note: The condition of the filter will affect the cleaner performance.
2
GB
07/08/2012 18.06.12